Intel D915PCML mATX 915P DDR2-533 LGA775 BOXD915PCML 用户手册
产品代码
BOXD915PCML
Product Description
27
For information about
Refer to
The location of the Serial ATA IDE connectors on the D915PCY board
Figure 18, page 60
The location of the Serial ATA IDE connectors on the D915PCM board
Figure 19, page 62
1.7.2.3
SCSI Hard Drive Activity LED Connector (Optional)
The SCSI hard drive activity LED connector is a 1 x 2-pin connector that allows an add-in
hard drive controller to use the same LED as the onboard IDE controller. For proper operation,
this connector should be wired to the LED output of the add-in hard drive controller. The LED
indicates when data is being read from, or written to, either the add-in hard drive controller or the
onboard IDE controller (Parallel ATA or Serial ATA).
hard drive controller to use the same LED as the onboard IDE controller. For proper operation,
this connector should be wired to the LED output of the add-in hard drive controller. The LED
indicates when data is being read from, or written to, either the add-in hard drive controller or the
onboard IDE controller (Parallel ATA or Serial ATA).
For information about
Refer to
The location of the SCSI hard drive activity LED connector on the D915PCY board
Figure 18, page 60
The location of the SCSI hard drive activity LED connector on the D915PCM board
Figure 19, page 62
The signal names of the SCSI hard drive activity LED connector
Table 25, page 65
1.7.3
Real-Time Clock, CMOS SRAM, and Battery
A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer
is not plugged into a wall socket, the battery has an estimated life of three years. When the
computer is plugged in, the standby current from the power supply extends the life of the battery.
The clock is accurate to
is not plugged into a wall socket, the battery has an estimated life of three years. When the
computer is plugged in, the standby current from the power supply extends the life of the battery.
The clock is accurate to
± 13 minutes/year at 25 ºC with 3.3 VSB applied.
✏
NOTE
If the battery and AC power fail, custom defaults, if previously saved, will be loaded into CMOS
RAM at power-on.
RAM at power-on.
1.8 PCI Express Connectors
The boards provide the following PCI Express connectors:
• One PCI Express x16 connector supporting simultaneous transfer speeds up to 8 GBytes/sec
• Two PCI Express x1 connectors. The x1 interfaces support simultaneous transfer speeds up to
• One PCI Express x16 connector supporting simultaneous transfer speeds up to 8 GBytes/sec
• Two PCI Express x1 connectors. The x1 interfaces support simultaneous transfer speeds up to
500 MBytes/sec
The PCI Express interface supports the PCI Conventional bus configuration mechanism so that the
underlying PCI Express architecture is compatible with PCI Conventional compliant operating
systems. Additional features of the PCI Express interface includes the following:
• Support for the PCI Express enhanced configuration mechanism
• Automatic discovery, link training, and initialization
• Support for Active State Power Management (ASPM)
• SMBus 2.0 support
• Wake# signal supporting wake events from ACPI S1, S3, S4, or S5
• Software compatible with the PCI Power Management Event (PME) mechanism defined in the
underlying PCI Express architecture is compatible with PCI Conventional compliant operating
systems. Additional features of the PCI Express interface includes the following:
• Support for the PCI Express enhanced configuration mechanism
• Automatic discovery, link training, and initialization
• Support for Active State Power Management (ASPM)
• SMBus 2.0 support
• Wake# signal supporting wake events from ACPI S1, S3, S4, or S5
• Software compatible with the PCI Power Management Event (PME) mechanism defined in the
PCI Power Management Specification Rev. 1.1