Atmel ATmega328P Xplained Mini MEGA328P-XMINI MEGA328P-XMINI 数据表
产品代码
MEGA328P-XMINI
124
ATmega48A/PA/88A/PA/168A/PA/328/P [DATASHEET]
Atmel-8271H-AVR- ATmega-Datasheet_08/2014
The timing diagram for the CTC mode is shown in
. The counter value (TCNT1) increases until a
compare match occurs with either OCR1A or ICR1, and then counter (TCNT1) is cleared.
Figure 16-6.
CTC Mode, Timing Diagram
An interrupt can be generated at each time the counter value reaches the TOP value by either using the OCF1A
or ICF1 Flag according to the register used to define the TOP value. If the interrupt is enabled, the interrupt
handler routine can be used for updating the TOP value. However, changing the TOP to a value close to
BOTTOM when the counter is running with none or a low prescaler value must be done with care since the CTC
mode does not have the double buffering feature. If the new value written to OCR1A or ICR1 is lower than the
current value of TCNT1, the counter will miss the compare match. The counter will then have to count to its
maximum value (0xFFFF) and wrap around starting at 0x0000 before the compare match can occur. In many
cases this feature is not desirable. An alternative will then be to use the fast PWM mode using OCR1A for
defining TOP (WGM13:0 = 15) since the OCR1A then will be double buffered.
or ICF1 Flag according to the register used to define the TOP value. If the interrupt is enabled, the interrupt
handler routine can be used for updating the TOP value. However, changing the TOP to a value close to
BOTTOM when the counter is running with none or a low prescaler value must be done with care since the CTC
mode does not have the double buffering feature. If the new value written to OCR1A or ICR1 is lower than the
current value of TCNT1, the counter will miss the compare match. The counter will then have to count to its
maximum value (0xFFFF) and wrap around starting at 0x0000 before the compare match can occur. In many
cases this feature is not desirable. An alternative will then be to use the fast PWM mode using OCR1A for
defining TOP (WGM13:0 = 15) since the OCR1A then will be double buffered.
For generating a waveform output in CTC mode, the OC1A output can be set to toggle its logical level on each
compare match by setting the Compare Output mode bits to toggle mode (COM1A1:0 = 1). The OC1A value will
not be visible on the port pin unless the data direction for the pin is set to output (DDR_OC1A = 1). The
waveform generated will have a maximum frequency of f
compare match by setting the Compare Output mode bits to toggle mode (COM1A1:0 = 1). The OC1A value will
not be visible on the port pin unless the data direction for the pin is set to output (DDR_OC1A = 1). The
waveform generated will have a maximum frequency of f
OC
1
A
= f
clk_I/O
/2 when OCR1A is set to zero (0x0000).
The waveform frequency is defined by the following equation:
The N variable represents the prescaler factor (1, 8, 64, 256, or 1024).
As for the Normal mode of operation, the TOV1 Flag is set in the same timer clock cycle that the counter counts
from MAX to 0x0000.
from MAX to 0x0000.
16.9.3 Fast PWM Mode
The fast Pulse Width Modulation or fast PWM mode (WGM13:0 = 5, 6, 7, 14, or 15) provides a high frequency
PWM waveform generation option. The fast PWM differs from the other PWM options by its single-slope
operation. The counter counts from BOTTOM to TOP then restarts from BOTTOM. In non-inverting Compare
Output mode, the Output Compare (OC1x) is cleared on the compare match between TCNT1 and OCR1x, and
set at BOTTOM. In inverting Compare Output mode output is set on compare match and cleared at BOTTOM.
Due to the single-slope operation, the operating frequency of the fast PWM mode can be twice as high as the
phase correct and phase and frequency correct PWM modes that use dual-slope operation. This high frequency
makes the fast PWM mode well suited for power regulation, rectification, and DAC applications. High frequency
allows physically small sized external components (coils, capacitors), hence reduces total system cost.
PWM waveform generation option. The fast PWM differs from the other PWM options by its single-slope
operation. The counter counts from BOTTOM to TOP then restarts from BOTTOM. In non-inverting Compare
Output mode, the Output Compare (OC1x) is cleared on the compare match between TCNT1 and OCR1x, and
set at BOTTOM. In inverting Compare Output mode output is set on compare match and cleared at BOTTOM.
Due to the single-slope operation, the operating frequency of the fast PWM mode can be twice as high as the
phase correct and phase and frequency correct PWM modes that use dual-slope operation. This high frequency
makes the fast PWM mode well suited for power regulation, rectification, and DAC applications. High frequency
allows physically small sized external components (coils, capacitors), hence reduces total system cost.
TCNTn
OCnA
(Toggle)
(Toggle)
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
or ICFn Interrupt Flag Set
(Interrupt on TOP)
1
4
Period
2
3
(COMnA1:0 = 1)
f
OCnA
f
clk_I/O
2 N
1 OCRnA
+
---------------------------------------------------
=