MULTIPLEX Funjet Ultra Power Set 332647 用户手册
产品代码
332647
Operating Instructions for Power Set “FunJET ULTRA”
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 1/2
O
p
er
at
in
g
I
n
st
ru
ct
io
n
s
fo
r
P
o
w
e
r
S
et
“F
u
n
J
E
T
U
L
T
R
A
”
#
8
2
6
0
1
7
(1
0
-0
3
-2
9
/D
A
M
A
)
E
rr
o
rs
a
n
d
o
m
is
s
io
n
s
e
x
c
e
p
te
d
!
M
U
L
T
IP
L
E
X
!
These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
The high-performance power set for very fast models
such as the FunJet ULTRA. The set is designed
specifically for maximum performance, and opens up a
new world of speed to the model pilot, including the ability
to accelerate vertically.
such as the FunJet ULTRA. The set is designed
specifically for maximum performance, and opens up a
new world of speed to the model pilot, including the ability
to accelerate vertically.
2. C
ONTENTS
/
R
EPLACEMENT PARTS
•
1 Himax C 3514-2900
# 33 3091
•
1 MULTIcont BL-70 S-BEC speed controller # 7 2287
•
1 6” x 5.5” propeller
# 73 3195
•
1 propeller driver with spinner for motor shafts
∅
4 mm,
prop-shaft 8 mm
# 33 2329
•
anodized alloy motormount
# 33 2606
•
Various small items for installation in the model
3. T
YP
.
O
PERATIONAL
D
ATA OF
P
OWER
S
ET
”F
UN
JET
ULTRA”
3S LiPo / 6” x 5.5” prop Current drain: approx. 65.0 A
Recommended flight battery:
MULTIPLEX Li-BATT FX 3/3200 # 15 7371
MULTIPLEX Li-BATT FX 3/3200 # 15 7371
Do not use the supplied Himax C 3514-2900 motor with
more than 3S LiPo or 9 NiXX cells when using the
recommended propellers.
more than 3S LiPo or 9 NiXX cells when using the
recommended propellers.
4. S
AFETY
N
OTES
The power set “FunJET ULTRA” is designed exclusively
for use in modelling applications. Incorrect use can result
in serious personal injury.
for use in modelling applications. Incorrect use can result
in serious personal injury.
•
Read the instructions before initiation
•
Before every flight, check that the motor and propeller
are securely mounted
•
Remove all movable objects from the area around the
propeller before switching the motor on
•
Do not allow clothing or any of your extremities to get
close to the spinning propeller
•
Never start running the motor in your hand
•
Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the
propeller blades
again; you may need to correct the balance of the
propeller blades
•
Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
5. A
SSEMBLING
O
F
T
HE
P
OWER
S
ET
”F
UN
JET
ULTRA”
1. Screw the motor to the motor mount.
2. Fit the split taper collet and the propeller driver on the
motor shaft.
3. Fit the propeller on the propeller driver, and secure
them with the spinner (supplied).
6. I
NITIATION OF THE
P
OWER
S
ET
“F
UN
JET
ULTRA”
1. Connect the three wires attached to the speed
controller to the three wires attached to the motor; the
order of connection is unimportant.
order of connection is unimportant.
2. Locate the UNI connector attached to the speed
controller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the “OFF” position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking
forward. If this is not the case, disconnect the flight
battery and swap over any two of the three motor wires.
forward. If this is not the case, disconnect the flight
battery and swap over any two of the three motor wires.
6. Switch off the motor brake at the speed controller; the
method of doing this is described in the instructions
supplied with the controller.
supplied with the controller.