MULTIPLEX Tucan 332663 用户手册
产品代码
332663
Operating Instructions for Power Set ”TUCAN & MENTOR”
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 1/2
O
p
e
ra
ti
n
g
I
n
s
tr
u
c
ti
o
n
s
f
o
r
P
o
w
e
r
S
e
t
“T
U
C
A
N
&
M
E
N
T
O
R
”
#
8
2
6
0
3
9
(
1
2
-1
1
-2
0
/B
R
A
N
)
E
rr
o
rs
a
n
d
o
m
is
s
io
n
s
e
x
c
e
p
te
d
!
M
U
L
T
IP
L
E
X
!
!
!
!
These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
Obtain the maximum performance, with the Power Set
“TUCAN & MENTOR” # 33 2663, from your trainer and
even use it for glider-towing. Suitable for trainers with a
maximum all-up weight of about 2200 g.
“TUCAN & MENTOR” # 33 2663, from your trainer and
even use it for glider-towing. Suitable for trainers with a
maximum all-up weight of about 2200 g.
2. C
ONTENTS
/
R
EPLACEMENT PARTS
•
1 Himax C 3528-1000 motor
# 33 3028
•
1 MULTIcont BL-55 S-BEC speed controller
# 7 2286
•
1 12” x 6” propeller
# 73 4344
•
1 propeller driver and nut M6 for spinner
Motor shaft-Ø 5mm, Prop-shaft 6 mm
# 33 2330
•
Various small items for installation in the model
3. T
YP
.
O
PERATIONAL
D
ATA OF
P
OWER
S
ET
“TUCAN
&
MENTOR”
3S LiPo / 12” x 6” prop Current drain: approx. 48.0 A*
* For current drain over 36 A use Li-BATT FX batteries!
Recommended flight battery:
MULTIPLEX Li-BATT FX 3/3200 # 15 7371
MULTIPLEX Li-BATT FX 3/3200 # 15 7371
Do not use the supplied Himax C 3528-1000 motor with
more than 3S LiPo or 9 NiXX cells when using the the
standard propeller.
more than 3S LiPo or 9 NiXX cells when using the the
standard propeller.
4. S
AFETY
N
OTES
The power set “TUCAN & MENTOR” is designed
exclusively for use in modelling applications. Incorrect
use can result in serious personal injury.
exclusively for use in modelling applications. Incorrect
use can result in serious personal injury.
•
Read the instructions before initiation
•
Before every flight, check that the motor and propeller
are securely mounted
•
Remove all movable objects from the area around the
propeller before switching the motor on
•
Do not allow clothing or any of your extremities to get
close to the spinning propeller
•
Never start running the motor in your hand
•
Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the
propeller
again; you may need to correct the balance of the
propeller
•
Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
5. A
SSEMBLING
O
F
T
HE
P
OWER
S
ET
“TUCAN
&
MENTOR“
1. Screw the motor to the motor mount
ensure that the
motor is free to rotate. When deploying the motor
cables, check that they must not make contact with the
spinning motor. Secure the motor leads with velcro tape
or similar.
cables, check that they must not make contact with the
spinning motor. Secure the motor leads with velcro tape
or similar.
2. Fit the split taper collet and the propeller driver on the
motor shaft.
3. Fit the propeller and the spinner holder on the propeller
driver, and secure them with the nut for the spinner
(supplied).
(supplied).
4. Clip the ELAPOR-spinner onto the spinner holder.
6. I
NITIATION OF THE
P
OWER
S
ET
“TUCAN
&
MENTOR”
1.
Connect the three wires attached to the speed
controller to the three wires attached to the motor; the
order of connection is unimportant.
controller to the three wires attached to the motor; the
order of connection is unimportant.
2.
Locate the UNI connector attached to the speed
controller, and connect it to your receiver.
controller, and connect it to your receiver.
3.
Switch the transmitter on, and check that the throttle
control is at the “OFF” position.
control is at the “OFF” position.
4.
Connect the flight battery to the speed controller.
5.
Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking
forward. If this is not the case, disconnect the flight
battery and swap over any two of the three motor wires.
spin clockwise when viewed from the tail, looking
forward. If this is not the case, disconnect the flight
battery and swap over any two of the three motor wires.
6.
Switch the speed controller’s motor brake OFF; refer to
the controller’s instructions for details of the procedure.
the controller’s instructions for details of the procedure.