Bluebird ARF 500 mm HC1327C 数据表
产品代码
HC1327C
www.hacker-model.eu
www.hacker-model.eu
6
3
HotWing
Kabely serv prostrčte drážkou skrz křídlo.
The servo cables put through the hole.
The servo cables put through the hole.
9
1
11
Zastrčte konektory serv, regulátoru a motoru do přijímače.
Označte si nejvhodnější umístění co nejblíž za uhlík 4 s ohledem
na délku kabelů. Na spodní straně křídla vyřízněte otvory pro
přijímač a regulátor. Otvor musí být ze všech stran o 1mm užší něž
přijímač a regulátor a hloubka musí být taková, aby byly zároveň
se spodní stranou křídla. Dále prořízneme zářezy pro kabely.
Přijímač, regulátor a kabely vlačte do vyřízlých otvorů.
Connect the motor with the ESC. Connect the ESC and servos
with the receiver. Mark the best position for placement of the
reciever and ESC close to carbon 4. Using sharp knife cut the slot
for the ESC and reciever. The slot must be 1mm smaller from each
side. The depth of the slot must be similar like thickness of the
ESC and receiver. Using sharp knife cut the slot for cables of the
servos, ESC and receiver. Push the ESC, receiver and cables to
the slot in the wings.
Označte si nejvhodnější umístění co nejblíž za uhlík 4 s ohledem
na délku kabelů. Na spodní straně křídla vyřízněte otvory pro
přijímač a regulátor. Otvor musí být ze všech stran o 1mm užší něž
přijímač a regulátor a hloubka musí být taková, aby byly zároveň
se spodní stranou křídla. Dále prořízneme zářezy pro kabely.
Přijímač, regulátor a kabely vlačte do vyřízlých otvorů.
Connect the motor with the ESC. Connect the ESC and servos
with the receiver. Mark the best position for placement of the
reciever and ESC close to carbon 4. Using sharp knife cut the slot
for the ESC and reciever. The slot must be 1mm smaller from each
side. The depth of the slot must be similar like thickness of the
ESC and receiver. Using sharp knife cut the slot for cables of the
servos, ESC and receiver. Push the ESC, receiver and cables to
the slot in the wings.
1
2
UBEC / ESC
Rx
Serva elevonů zajistěte několika kapkami vteřinového lepidla
mezi lepenkou a materiálem křídla. Nasaďte táhla elevonů 9 do
páky elevonu 10 a poté do konektoru serva 7. Zajistěte šroubkem
ve správné poloze.
Glue servos in place with a few drops of CA and CA Accelerator.
Insert pushrod 9 into control horn 10 and then to the
connector 7 and tighten the screw.
mezi lepenkou a materiálem křídla. Nasaďte táhla elevonů 9 do
páky elevonu 10 a poté do konektoru serva 7. Zajistěte šroubkem
ve správné poloze.
Glue servos in place with a few drops of CA and CA Accelerator.
Insert pushrod 9 into control horn 10 and then to the
connector 7 and tighten the screw.
12
2
Spodní strana
Bottom Side
Bottom Side
Spodní strana
Bottom Side
Bottom Side
Horní strana
Upper Side
Upper Side
10
CA
10
Slot
2
10
Pomocí RC soupravy nastavte serva do neutrálu. Nasaďte páky a
vmáčkněte serva do křídel 1 a 2. Naznačte si umístění pák
křidélek 10 a modelářským nožem prořízněte do křidélek drážky
podle obrázku. Páky zatlačte do drážek a zalepte je řídkým
vteřinovým lepidlem a zastříkněte aktivátorem.
Switch on the RC system and set the servos to neutral. Push the
servos into the holes in the wing panels 1 and 2. Mark positions
and
vmáčkněte serva do křídel 1 a 2. Naznačte si umístění pák
křidélek 10 a modelářským nožem prořízněte do křidélek drážky
podle obrázku. Páky zatlačte do drážek a zalepte je řídkým
vteřinovým lepidlem a zastříkněte aktivátorem.
Switch on the RC system and set the servos to neutral. Push the
servos into the holes in the wing panels 1 and 2. Mark positions
and
cut the slots for control horns 10 as shown.
using sharp knife
Insert control horns into the slots and glue with CA glue and CA
Accelerator.
Accelerator.
Horní strana
Upper Side
Upper Side
4
13
Zasuňte Winglety 3 do drážek v křídle a zkontrolujte souosost se
středem křídla. Zalepte řidkým vteřinovým lepidlem z horni i
spodní strany křídla. Zastříkněte aktivátorem.
Insert the winglets 3 to the slot in the wing and check the
alignment. Glue winglets with CA glue and CA Accelerator from
the top and bottom wing.
středem křídla. Zalepte řidkým vteřinovým lepidlem z horni i
spodní strany křídla. Zastříkněte aktivátorem.
Insert the winglets 3 to the slot in the wing and check the
alignment. Glue winglets with CA glue and CA Accelerator from
the top and bottom wing.
CA
2
3
2
1
3
Horní strana
Upper Side
Upper Side
1
10
9
7
14
Přilepte lože motoru 5 vteřínovým lepidlem k držáku motorového
lože 6 podle obrázku. Lože motoru 5 musí byt kolmo k držákům
lože motoru 6!!!.
Glue engine mounts 5 with
lože 6 podle obrázku. Lože motoru 5 musí byt kolmo k držákům
lože motoru 6!!!.
Glue engine mounts 5 with
as shown.
Bracket engine mount 7
Glue it together with CA glue.
E n g i n e m o u n t 5 m u s t b e p e r p e n d i c u l a r t o t h e
bracket 6!!!.
E n g i n e m o u n t 5 m u s t b e p e r p e n d i c u l a r t o t h e
bracket 6!!!.
5
6
CA