Renkforce SATA harddrive casing 2.5 " T2545UAA USB 3.0 T2545UAA 用户手册

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). 
All  rights  including  translation  reserved.  Reproduction  by  any  method,  e.g.  photocopy,  microfilming,  or  the  capture  in  electronic  data 

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the 

technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE. 

V2_0215_02_HK

•  Your operating system has the drivers necessary for the hard drive casing, thus 

there is no data storage device containing drivers included in delivery.

•  When you first connect the hard drive casing with your built-in hard drive/SSD to a 

USB port (see the chapter “Connection”), Windows

®

 will recognize new hardware. 

Wait until the installation has been completed. That should only take a few seconds.

•   Do not move the product with your built-in hard drive during operation. If moved 

during operation, the write/read heads inside the hard drive could touch the 

magnetic disc. This may result not only in data loss but damage to the hard drive! 

Also avoid moving the product for up to 30 seconds after disconnecting it from the 

computer, until the hard drive’s magnetic discs come to a stop.

•  Disregard this warning for use with an SSD, as an SSD contains no moving parts.
•  Do not install the hard drive casing vertically, since a mounted hard drive could get 

damaged if tipped over (especially if the hard drive is currently in use).

•  Connect the USB 3.0 cable to the hard drive casing and the USB 3.0 port on your 

computer. A standard USB 3.0 port supplies a current of max. 900 mA. This is 

sufficient for the hard drive casing and a built-in hard drive (or SSD).

•  In some cases, notebooks or non-standard USB 3.0 ports may supply less current. In 

such cases, an appropriate USB 3.0 hub with a separate power supply is necessary 

for operation.

According to USB standard, a USB 2.0 port can supply a current of up to 

500 mA. The hard drive casing and a built-in hard drive require more current 

than 500 mA, operation is not possible using this port.

A new hard drive must be partitioned and formatted before the drive can be 

recognized and used by, for instance, Windows

®

 File Manager.

•  Windows

®

 8, 7, Vista

TM

 or Windows

®

 XP allow for easy partitioning and formatting 

via control panel (and from there via computer management/disk management). 

•  After partitioning, the new partition must be formatted (quick formatting is sufficient; 

performing “normal” formatting procedures could otherwise take very long to 

complete, depending on the size of the hard drive/SSD).

•  Only after the hard drive/SSD has been partitioned and subsequently formatted can 

data be saved to the hard drive/SSD.

•   Once the USB 3.0 port (2) is supplied with current, the hard drive/SSD starts running 

and the blue LED (3) lights up.

•  The red LED (4) lights up during data transfer.
•  Disconnect the USB 3.0 cable from the computer and hard drive casing after all 

LEDs have turned off and if the product is not going to be used any further.

•  To protect the hard drive casing from dust, store it in the storage bag provided.

•  Disconnect the product from the power supply (USB port) before each cleaning. 
•  Besides occasional cleaning, the device is maintenance-free. To clean the device, 

use a soft, anti-static and lint-free cloth. To prevent scratch marks, do not apply too 

much force on the surface during cleaning.

•  Do not use any abrasive or chemical cleaners.
•  Never submerge the product in water.

Electronic devices are recyclable waste and must not be disposed of in the 

household waste.
At the end of its service life, dispose of the product according to the 

relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of 

the environment.

Operating voltage/current .................5 V/DC, max. 900 mA (via USB)
Interface/connection standard ........USB 3.0 
Supported hard drives/SSD............... SATA, 6.35 cm/2.5”, of 5 mm / 7 mm / 9.5 mm in 

height and of up to 2 TB in storage capacity

SATA support ....................................... SATA I / II / III (for SATA III, max. data transfer 

rate is the same as for SATA II)

Supported operating systems ........... Windows

®

 XP (Home, Pro, with SP1, SP2, SP3), 

only 32 bit, Vista™ (32 / 64 bit), 7 (32 / 64 bit),  

8.0 (32 / 64 bit), 8.1 (32 / 64 bit), 

Mac OS X 10.1 and higher 

Linux 2.6.31 and higher

Operating conditions  .........................0 to +70 °C, 20 - 80 % RH
Storage conditions..............................-20 to +65 °C, 10 - 80 % RH
Dimensions (W x H x D)......................76 x 13 x 139 mm
Weight ...................................................approx. 90 g