Behringer Minimon MON800 快速安装指南
(1)
(2)
(3)
(8)
(11)
(12)
(13)
(6)
(4)
(7)
(9)
(10)
(5)
(14)
(17)
(16)
(15)
(18)
(19)
(20)
(21)
(22)
MINIMON MON800
Controls
(EN)
Controls
(10)
Use the TALK LEVEL control
to adjust the sensitivity of the
talk-back microphone.
to adjust the sensitivity of the
talk-back microphone.
(11)
The talk-back microphone is
installed behind the MIC openings.
Speak into the microphone to
make announcements which
are then routed to the recording
devices connected to the
2-TRACK OUT outputs.
installed behind the MIC openings.
Speak into the microphone to
make announcements which
are then routed to the recording
devices connected to the
2-TRACK OUT outputs.
(12)
The TALK TO CUE/PHONES/SPK
A and TALK TO 2-TR OUT buttons
determine where the talk-back
microphone signal is routed to
A and TALK TO 2-TR OUT buttons
determine where the talk-back
microphone signal is routed to
(9)
.
(13)
The switch turns your MINIMON
MON800 on and off.
MON800 on and off.
(14)
The MON800 is connected to the
mains using a 2-pole POWER
connector jack. A matching mains
adaptor is included with the unit.
mains using a 2-pole POWER
connector jack. A matching mains
adaptor is included with the unit.
(15)
A second pair of headphones
can be connected to the PH jack.
This connector is wired in parallel
with the front-panel jack
can be connected to the PH jack.
This connector is wired in parallel
with the front-panel jack
(3)
.
(16)
The TB jack is used to connect a single
footswitch
footswitch
(12)
.
(17)
Two pairs of loudspeakers can be
connected to the SPEAKERS OUT B
and C jacks.
connected to the SPEAKERS OUT B
and C jacks.
(18)
Connect your main monitor speakers
to the SPEAKERS OUT A jack.
to the SPEAKERS OUT A jack.
(19)
CUE OUT is an additional output,
which you can use to route
the MINIMON signals to other
devices, such as an additional
headphones amp.
which you can use to route
the MINIMON signals to other
devices, such as an additional
headphones amp.
(20)
The two 2-TRACK OUT jacks are
wired in parallel and carry the
same signals. Use the ¼" or cinch
outputs, depending on the recording
device used.
wired in parallel and carry the
same signals. Use the ¼" or cinch
outputs, depending on the recording
device used.
(21)
Use the CD/TAPE IN jacks C and D to
connect playback devices, such as a
computer, CD/MD or cassette player.
connect playback devices, such as a
computer, CD/MD or cassette player.
(22)
The MIX IN jacks A and B are for
connecting the main signal sources
(e.g. mixing console, audio card, etc.)
using ¼" plugs. Mono signals must be
connected to the L jacks.
connecting the main signal sources
(e.g. mixing console, audio card, etc.)
using ¼" plugs. Mono signals must be
connected to the L jacks.
(1)
Use the four switches in the SOURCE
section to select up to four input
sources (MIX A and B, CD/TAPE C and D)
for monitoring and recording.
section to select up to four input
sources (MIX A and B, CD/TAPE C and D)
for monitoring and recording.
(2)
The two LED displays are for
monitoring the output level of the
2-TRACK OUT outputs. They comprise
6 LEDs each. When the CLIP LED lights
up, this indicates that distortion
may occur.
monitoring the output level of the
2-TRACK OUT outputs. They comprise
6 LEDs each. When the CLIP LED lights
up, this indicates that distortion
may occur.
(3)
A pair of headphones with a ¼" TRS
connector (e.g. BEHRINGER HPS5000)
can be connected to the PHONES jack.
This output is wired in parallel with the
rear-panel output jack
connector (e.g. BEHRINGER HPS5000)
can be connected to the PHONES jack.
This output is wired in parallel with the
rear-panel output jack
(15)
, so that up
to two headphones can be used at the
same time.
same time.
(4)
With the PHONES LEVEL control you
can adjust the volume for the two
headphones jacks on the front or rear
panel respectively.
can adjust the volume for the two
headphones jacks on the front or rear
panel respectively.
(5)
SPK A LEVEL governs the volume
level of the SPEAKERS OUT A outputs
level of the SPEAKERS OUT A outputs
(18)
. SPK B + C LEVEL allows you to
set the volume for outputs B and C
(17)
simultaneously.
(6)
Use the switches A/B/C ON to switch
the speakers A, B and C on and off.
the speakers A, B and C on and off.
(7)
With the MUTE switch you can
disable all loudspeaker and
headphones outputs.
disable all loudspeaker and
headphones outputs.
(8)
The MONO switch switches all monitor
paths to mono.
paths to mono.
(9)
The DIM switch lowers the level of the
monitor paths by -20 dB. This allows
you, for example, to talk to somebody
while mixing without losing track of
the recording.
monitor paths by -20 dB. This allows
you, for example, to talk to somebody
while mixing without losing track of
the recording.
8
MINIMON MON800
9
Quick Start Guide
Check Out behringer.com for
Full Manual