Ikelite Nikonos TTL Cord Film Camera 产品宣传页
IIKKEELLIITTEE SSIIN
NGGLLEE CCO
ORRD
D//
N
NIIKKO
ON
NO
OSS--SSTTYYLLEE #
#44110044..66
SSIIN
NGGLLEE SSYYN
NCC CCO
ORRD
D #
#44110044..66____________________________________
Connects a single (1) Ikelite Substrobe to a Nikonos IV, V, RS camera or
suitable FILM camera housing that utilizes the Nikonos-style flash socket
for external strobe connection. The strobes will fire in TTL automatic or
manual exposure modes using the Nikons V or RS. Strobes will only work
in the manual mode with the Nikonos IV or camera housings.
O
ON
NLLYY IIKKEELLIITTEE TTTTLL SSU
UBBSSTTRRO
OBBEESS CCAAN
N BBEE CCO
ON
NN
NEECCTTEEDD..
D
DO
O N
NO
OTT use the TTL cord on a non TTL strobe; you will damage
the camera.
D
DO
O N
NO
OTT remove the sync cord from the strobe or camera underwater
or when wet. Connections are NOT waterproof when
disconnected underwater.
D
DO
O N
NO
OTT leave the cord connected
for prolonged periods. Otherwise,
the cord may freeze to the strobe
or camera. After each dive,
disconnect the cord and lightly
lubricate the connector threads.
Never use spray lubricant.
Nikonos Style
Connector
CCO
ON
NN
NEECCTTIIN
NGG TTH
HEE SSTTRRO
OBBEE __________________________________________________________________________
1. Make sure all components are dry.
2. Clean and lightly lubricate the stem o-ring and the strobe
2. Clean and lightly lubricate the stem o-ring and the strobe
connector threads. Check the o-ring for nicks or cuts.
3. Note the positioning of the receptacles and pins.
Properly align the end of the sync cord and insert into
the strobe connector.
4. Hand-tighten the Retaining ring on the sync cord.
5. Push the connector body further into the strobe connector
5. Push the connector body further into the strobe connector
and continue to tighten the Retaining ring.
CCO
ON
NN
NEECCTTIIN
NGG TTO
O TTH
HEE CCAAM
MEERRAA O
ORR H
HO
OU
USSIIN
NGG________________________________________
1. Make sure all components are dry. Clean and lightly
lubricate the stem shaft, o-ring and retaining ring threads.
Check the stem o-ring for nicks or cuts.
2. Align the index groove with the Indexing Pin of the flash
socket, and insert the stem into the flash socket.
3. Rotate the retaining ring counter clockwise until it
mates with the flash socket threads. Then carefully
rotate retaining ring clockwise and thread it into the
flash socket until snug.
LLIIM
MIITTEED
D W
WAARRRRAAN
NTTYY______________________________________________________________________________________
All Ikelite products are warranted against any manufacturing defects for
a period of one (1) year from the date of purchase. Defective products
should be returned prepaid to Ikelite. Ikelite will, at its discretion, repair or
replace such products, and will return to customer prepaid. All other claims,
of any nature, including but not limited to bulb failure are not covered. Except
as mentioned above, no other warranty expressed or implied, applies to this
Ikelite product.
IIKKEELLIITTEE U
UN
ND
DEERRW
WAATTEERR SSYYSSTTEEM
MSS
50 West 33rd Street, P.O. Box 88100,
Indianapolis, IN 46208 USA
(317) 923-4523
4104.6-01-0706
Retaining
Ring
Ring
Index Groove
Stem O'ring
Red Retainer
O'ring
O'ring
Retaining
Ring
Ring
Index Groove
Stem O'ring
Red Retainer
O'ring
O'ring
Blue
Band
Band
Retaining
Ring
Ring
Stem O'ring
Retaining
Ring
Ring
Stem O'ring