HeadRoom Headphone Amplifier & Digital-Analog Converter 用户手册
2
3
The Micro Amp
Front Panel
1. Line Input
The line input is where you plug in the source. Preferably the Micro
DAC; but it could be the line out of your iRiver or the headphone out of an iPod. You
will need a mini-to-mini cable to hook up your Micro Amp.
will need a mini-to-mini cable to hook up your Micro Amp.
2. Headphone Out
The headphone out is where you plug in your headphones.
There isn’t room for a full sized jack, but this 1/8th inch mini-plug will take the small
plug of all 1/8” headphone jacks. We also sell a short flexible Grado 1/4”-1/8”
adaptor for your big cans; and you can get a replacable Cardas headphone cable
with a mini connector for many types of headphones, call us or consult our website
for details.
plug of all 1/8” headphone jacks. We also sell a short flexible Grado 1/4”-1/8”
adaptor for your big cans; and you can get a replacable Cardas headphone cable
with a mini connector for many types of headphones, call us or consult our website
for details.
3. Crossfeed Switch
This switch engages the crossfeed circuit. The audio image
on headphones is often not very good; typically the image is a blob on the left, a blob
on the right, and a blob in the middle. The HeadRoom crossfeed provides the natural
acoustic cross-feed normally heard at the left and right ear as heard from the left and
right speaker. Adding back the normally occurring cross-feed signal gives your brain
enough information to build the stable and natural audio image needed to have a
quality listening experience. See pg.8 for more info on the HeadRoom crossfeed.
on the right, and a blob in the middle. The HeadRoom crossfeed provides the natural
acoustic cross-feed normally heard at the left and right ear as heard from the left and
right speaker. Adding back the normally occurring cross-feed signal gives your brain
enough information to build the stable and natural audio image needed to have a
quality listening experience. See pg.8 for more info on the HeadRoom crossfeed.
4. Gain Switch
The 3-position Gain Switch accomodates various headphones’
power needs. For instance, the Low Gain setting would be used for in-ear monitors,
allowing a larger range on the volume control pot. Experiementing with your
headphones and the gain switch may help you to determine which setting you prefer.
If have any questions regarding your headphones, feel free to call and ask us.
allowing a larger range on the volume control pot. Experiementing with your
headphones and the gain switch may help you to determine which setting you prefer.
If have any questions regarding your headphones, feel free to call and ask us.
5. Volume Control
You never know where the volume control should be set as
different headphones often have widely different impedances and efficiencies, so use
your ears to choose your listening level, not the level on the dial. (We recommend you
choose a moderate level so as not to blow out your ears.) You also need to turn the
amp OFF or ALL THE WAY DOWN before plugging in or unplugging your headphones
to avoid short-circuiting the amp. As you turn the volume control knob clockwise,
the volume increases.
your ears to choose your listening level, not the level on the dial. (We recommend you
choose a moderate level so as not to blow out your ears.) You also need to turn the
amp OFF or ALL THE WAY DOWN before plugging in or unplugging your headphones
to avoid short-circuiting the amp. As you turn the volume control knob clockwise,
the volume increases.
6. Power Source Switch
Immediately to the right of the volume control is the
power source switch. It will run on either the two internal 9-Volt batteries or an external
power supply. If the batteries are in and external supply is attached, the only way
you can turn it off is by selecting ‘external’ and then unplugging the connector. We
offer two power supplies: the less expensive, lovingly known as “brick”, power supply
comes with the amp, the more expensive Desktop Power Supply will give you cleaner
juice, and therefore cleaner, more dynamic sound.
power supply. If the batteries are in and external supply is attached, the only way
you can turn it off is by selecting ‘external’ and then unplugging the connector. We
offer two power supplies: the less expensive, lovingly known as “brick”, power supply
comes with the amp, the more expensive Desktop Power Supply will give you cleaner
juice, and therefore cleaner, more dynamic sound.
Rear Panel
7. External Power Input
Connect either your brick or Desktop Power Supply
here.
8. Thumb Screws
To change your batteries, unscrew the screws and remove the
rear panel. Orientation of 2 nine-volt batteries is indicated by the illustrations on
the rear panel.
the rear panel.
Packing HeadRoom’s mobile electronics module, two nine-volt batteries, and
all the knobs and switches you need into an all but bullet proof aluminum
enclosure is pushing it a bit, but you won’t care because your head will be
thanking you for the lovely tunes.
all the knobs and switches you need into an all but bullet proof aluminum
enclosure is pushing it a bit, but you won’t care because your head will be
thanking you for the lovely tunes.
1.
Line
Input
2.
Headphone
Out
3.
Crossfeed
Switch
5.
Volume
Control
6.
Power
Source
Switch
7.
External Power Input
8.
Thumb Screws
The Micro Amp Panel Descriptions
4.
Gain
Switch