Behringer Europack UB2442FX-Pro 业主指南

EURORACK UB2442FX-PRO/UB2222FX-PRO/UB1832FX-PRO/UB1622FX-PRO User Manual

UB2442FX-PRO

Fig. 5.1: Main Mix outputs, main mix insert points and control room outputs

MAIN OUTPUTS
The MAIN outputs carry the MAIN MIX signal and are on balanced XLR jacks with 

a nominal level of +4 dBu. In parallel with this, 1/4" phone jacks carry the main 

mix signal in a balanced format (UB1622FX-PRO: here, the phone jack outputs are 

unbalanced and located on the front panel).

CONTROL ROOM OUTPUTS (CTRL OUT)
The control room output is normally connected to the monitoring system in the 

control room and carries the stereo mix or, when selected, the solo signals.

MAIN INS(ERTS) (UB2442FX-PRO only)
These are the insert points for the main mix. In the signal path, they are 

post-main mix amp, but pre-main fader(s). Use them to insert, for example, 

a dynamics processor or graphic equalizer. Please also note the information on 

insert points in chapter 5.3.

UB2442FX-PRO

Fig. 5.2: Subgroup outputs

SUB OUTPUTS
The subgroup outputs are unbalanced and provide the mix of those channels 

assigned to each subgroup with the SUB switch (UB2442FX-PRO: switches 1-2 

or 3-4) next to the channel faders. Thus, you can, for example, route a subgroup 

to a second console or use the output as a recording output in parallel to the 

main outputs. In this way, you can record several tracks simultaneously. With an 

8-track recorder, use Y cables and wire the inputs of your machine so that you 

have 2 x 4 tracks available (e.g. channel 1 to track 1 and 2, etc.). In the first pass, 

you can record the tracks 1, 3, 5 and 7, in the second the tracks 2, 4, 6 and 8.
The EURORACK UB2442FX-PRO already has subgroup outputs wired in parallel 

(1-5, 2-6, etc.).

UB1622FX-PRO

Fig. 5.3: Insert points

Insert points are very useful to process channel signals with dynamic processors 

or equalizers. Unlike reverb or other effects devices, whose signals are usually 

added to the dry signal, dynamic processors are most effective on the complete 

signal. In this case, aux send paths are a less-than-perfect solution. It is better 

to interrupt the signal path and insert a dynamic processor and/or equalizer. 

After processing, the signal is routed back to the console at precisely the same 

point it left. However, the channel signal path is interrupted only if a plug is 

inserted into the corresponding jack (stereo phone plug: tip = signal output; 

ring = return input). All mono input channels are equipped with inserts. 
They are pre-fader, pre-EQ and pre-aux send. Inserts can also be used as pre-EQ 

direct outputs, without interrupting the signal path. To this end, you will need 

a cable fitted with mono phone plugs on the tape machine or effect device end, 

and a bridged stereo phone plug on the console side (tip and ring connected).

UB2442FX-PRO

Fig. 5.4: Direct outputs 

DIRECT OUTPUTS
The direct outputs of the UB2442FX-PRO (1 each per mono input channel) 

are ideal for recording if several tracks are to be recorded simultaneously. 

These unbalanced phone jacks are post-EQ, post-mute and post-fader.

All models

Fig. 5.5: Voltage supply and fuse

FUSE HOLDER/IEC MAINS RECEPTACLE
The console is connected to the mains via the cable supplied, which meets the 

required safety standards. Blown fuses must only be replaced by fuses of the 

same type and rating. The mains connection is made via a cable with IEC mains 

connector. An appropriate mains cable is supplied with the equipment.