Whirlpool Gas Dryers 用户手册

Lint should be removed every 2 years, or more often, depending 
on dryer usage. Cleaning should be done by a qualified person.

Lint should be removed every 2 years, or more often, depending 
on dryer usage.

The dryer light automatically turns on inside the dryer drum when 
you open the door.

Unplug dryer or disconnect power.

Open the dryer door. Locate the light bulb cover on the back 
wall of the dryer. Remove the screw located in the lower right 
corner of the cover. Remove the cover.

Turn bulb counterclockwise. Replace the bulb only with a 
10-watt appliance bulb. Replace the cover and secure with 
the screw.

Plug in dryer or reconnect power.

■

For error message “PF” (power failure), check the 
following:
Is the dryer connected to the power supply? 

Was the dryer connected to a power supply during 
installation or a power failure?
Press START to resume operation or press STOP/CANCEL to 
cancel the cycle.

Was the drying cycle interrupted by a power failure? 
Press START to resume operation or press STOP/CANCEL to 
cancel the cycle.

■

For error message “E1” or “E2” (service codes):
Service is required, call for service.

■

Check the following:
Is the lint screen clogged with lint?

Is the exhaust vent or outside exhaust hood clogged with lint, 
restricting air movement? Run the dryer for 
5-10 minutes. Hold your hand under the outside exhaust 
hood to check air movement. If you do not feel air movement, 
clean exhaust system of lint or replace exhaust vent with a 
heavy metal or flexible metal vent. See your Installation 
Instructions.

Is the exhaust vent crushed or kinked? Replace with a heavy 
metal or flexible metal vent. See your Installation Instructions. 

Has a fuse blown, or a circuit breaker tripped? Electric dryers 
use 2 household fuses or breakers. The drum may be turning 
but you may not have heat.

Has an air dry cycle been selected? Select the right cycle for 
the types of garments being dried. See “Drying, Cycle and 
Temperature Tips.”

Is the automatic cycle ending early? The load may not be 
contacting the electronic sensor strips, level the dryer.

For gas dryers, is the valve open on the supply line? 

Are fabric softener sheets blocking the grille? Use only one 
fabric softener sheet and only use it once.

■

Is the dryer located in a room with temperature below 
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above 
45ºF (7ºC).

■

Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water 
and with items that hold moisture (cottons). 

■

Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.

■

Check the following:
Is the power cord plugged in?

Has a fuse blown, or has circuit breaker tripped?

Was a regular fuse used? Use a time-delay fuse.

Is the dryer door firmly closed?

Was the START pad firmly pressed?

Is a cycle selected?

■

Has the dryer had a period of non-use? 
If the dryer hasn’t been used for a while, there may be a 
thumping sound during the first few minutes of operation. 

■

Is it a gas dryer? 
The gas valve clicking is a normal operating sound.

■

Is the lint screen clogged?
Clean lint screen. Check for air movement.

■

Is the load properly sorted?
Sort lint givers (towels, chenille) from lint takers (corduroy, 
synthetics). Also sort by color.

■

Is the load too big or too heavy?
Dry smaller loads so lint can be carried to the lint screen.

■

Was the load overdried?
Use correct dryer settings for load type. See “Drying, Cycle 
and Temperature Tips.”  Overdrying can cause lint-attracting 
static electricity.

■

Was paper or tissue left in pockets?
Clean out pockets before drying.

■

Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and 
laundering.

■

Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.  
Fabric softener sheets added to a partially-dried load can 
stain garments.