Whirlpool 8314832A 用户手册

■

Check the following:
Is the lint screen clogged with lint?

Is the exhaust vent or outside exhaust hood clogged with lint, 
restricting air movement? Run the dryer for 5-10 minutes. 
Hold your hand under the outside exhaust hood to check  air 
movement. If you do not feel air movement, clean exhaust 
system of lint or replace exhaust vent with heavy metal or 
flexible metal vent. See your Installation Instructions.

Is the exhaust vent crushed or k ink ed? Replace with heavy 
metal or flexible metal vent. See your Installation Instructions. 

Has a fuse blown, or a circuit break er tripped? Electric dryers 
use 2 household fuses or break ers. The drum may be turning 
but you may not have heat.

Has an Air Dry cycle been selected? Select the right cycle for 
the types of garments being dried (see “Drying, Cycle and 
Temperature Tips”).

For gas dryers, is the valve open on the supply line? 

Are fabric softener sheets block ing the grill? Use only one 
fabric softener sheet and only use it once.

■

Is the dryer located in a room with temperature below 
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above 
45ºF (7ºC).

■

Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water 
and with items that hold moisture (cottons). 

■

Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.

:

Is the power cord plugged in?

Has a fuse blown, or has circuit break er tripped?

Was a regular fuse used? Use a time-delay fuse.

Is the dryer door firmly closed?

Was the START button firmly pressed?

Is a cycle selected?

■

Has the dryer had a period of non-use? 
If the dryer hasn’t been used for a while, there may be a 
thumping sound during the first few minutes of operation. 

■

 

The gas valve click ing is a normal operating sound.

■

Is the lint screen clogged?
Clean lint screen. Check  for air movement.

■

Is load properly sorted?
Sort lint givers (towels, chenille) from lint tak ers (corduroy, 
synthetics). Also sort by color.

■

Is the load too big or too heavy?
Dry smaller loads so lint can be carried to the lint screen.

■

Was the load overdried?
Use correct dryer settings for load type (see “Drying, Cycle 
and Temperature Tips”). Overdrying can cause lint-attracting 
static electricity.

■

Was paper or tissue left in pockets?
Clean out pock ets before drying.

■

Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and 
laundering.

■

Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle. 
Fabric softener sheets added to a partially-dried load can 
stain your garments.

■

Were items soiled when placed in the dryer?
Items should be clean before being dried.

■

Were items properly sorted?
Sort light colors from dark  colors. Sort colorfast items from 
noncolorfast items.

■

Was the dryer overloaded?
Dry smaller loads that can tumble freely.

■

Did the load overdry?
Check  the manufacturer’s care label. Match dryer setting to 
load type (see “Drying, Cycle and Temperature Tips”).

■

Was load removed from dryer at the end of the cycle?
Remove load as soon as tumbling stops.

■

Was dryer overloaded?
Dry smaller loads that can tumble freely.

■

Did load overdry?
Check  the manufacturer’s care label. Match dryer setting to 
load type (see “Drying, Cycle and Temperature Tips”).

■

If the dryer is electric, is it being used for the first time?
The new electric heating element may have an odor. The odor 
will be gone after the first cycle.

■

:

Turn off the gas supply line, leave your house and then call 
your local gas company. 

■

Have you recently been painting, staining or varnishing in 
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone 
from the area, re-wash the clothing and then dry it.