Whirlpool MDBH949PAM 手册
6
OPTION SELECTIONS
OPTIONS
dish load types
DESCRIPTIONS
USE WITH:
ADDED
TIME TO
CYCLE
Tough food soils
Adds heat and wash time to the
cycle.
cycle.
Jetclean
®
Plus Steam, Normal,
and Auto Clean
30 min.
Tough food soils
Increases the target water
temperature during the wash portions
of the cycle. Adds heat, time, and
water.
temperature during the wash portions
of the cycle. Adds heat, time, and
water.
Jetclean
®
Plus Steam, Normal,
and Auto Clean
10 min.
All loads
Use for best drying results in
combination with rinse aid. Turn off
when loads contain plastic
dinnerware that may be sensitive to
higher temperatures.
combination with rinse aid. Turn off
when loads contain plastic
dinnerware that may be sensitive to
higher temperatures.
Jetclean
®
Plus Steam, Normal,
Light, Quick Wash and Auto Clean
45 min.
To sanitize your dishes
and glassware
and glassware
Raises the water temperature in the
final rinse to approximately 154°F
(68°C). This high temperature rinse
sanitizes your dishes and glassware
in accordance with NSF/ANSI
Standard 184 for Residential
Dishwashers. Certified residential
dishwashers are not intended for
licensed food establishments. The
Sanitize option adds heat and time to
the cycle.
final rinse to approximately 154°F
(68°C). This high temperature rinse
sanitizes your dishes and glassware
in accordance with NSF/ANSI
Standard 184 for Residential
Dishwashers. Certified residential
dishwashers are not intended for
licensed food establishments. The
Sanitize option adds heat and time to
the cycle.
Jetclean
®
Plus Steam, Normal,
and Auto Clean
30 min.
All loads
Delays the start of a cycle up to
8 hours.
8 hours.
All cycles
120, 240,
480 min.
All loads
When Control Lock is lit, all buttons
are disabled. If you press any pad
while your dishwasher is locked, the
light flashes. The door can be opened
while the controls are locked.
are disabled. If you press any pad
while your dishwasher is locked, the
light flashes. The door can be opened
while the controls are locked.
All cycles
CONTROLS AND CYCLE STATUS
CONTROL
PURPOSE
COMMENTS
To start or resume a
wash cycle
wash cycle
If the door is opened during a cycle or the power is interrupted, the START/RESUME
indicator flashes. The cycle will not resume until the door is closed and START/RESUME is
pressed.
indicator flashes. The cycle will not resume until the door is closed and START/RESUME is
pressed.
NOTE: If the START/RESUME button is located on top of door, push door firmly closed
within 3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds,
the start button LED will flash, an audible tone will be heard, and the cycle will not start.
within 3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds,
the start button LED will flash, an audible tone will be heard, and the cycle will not start.
To reset any cycle or
options during
selection.
options during
selection.
To cancel a wash
cycle after it's
started.
cycle after it's
started.
Press CANCEL/DRAIN to reset any control selections made.
See “Canceling A Cycle” and “Changing A Cycle After Dishwasher Is Started” sections.
To turn the audible
tones on or off.
tones on or off.
Press and hold the Hi Temp Wash button for 3 seconds to turn the audible tones on or off.
Only audible tones for confirming button presses can be turned on/off. Important audible
tones, such as indicating a cycle has been interrupted, cannot be deactivated.
NOTE: Audible tones are not available on all models.
Only audible tones for confirming button presses can be turned on/off. Important audible
tones, such as indicating a cycle has been interrupted, cannot be deactivated.
NOTE: Audible tones are not available on all models.