Spectrum Brands MC.31XX 用户手册
100
MC.31xx Manual
Error Codes
Appendix
Appendix
Error Codes
The following error codes could occur when a driver function has been called. Please check carefully the allowed setup for the register and
change the settings to run the program.
change the settings to run the program.
error name
value (hex)
value (dec.)
error description
ERR_OK
0h
0
Execution OK, no error.
ERR_INIT
1h
1
The board number is not in the range of 0 to 15. When initialisation is executed: the board number is yet
initialised, the old definition will be used.
initialised, the old definition will be used.
ERR_NR
2h
2
The board is not initialised yet. Use the function SpcInitPCIBoards first. If using ISA boards the function SpcIn-
itBoard must be called first.
itBoard must be called first.
ERR_TYP
3h
3
Initialisation only: The type of board is unknown. This is a critical error. Please check whether the board is
correctly plug in the slot and whether you have the latest driver version.
correctly plug in the slot and whether you have the latest driver version.
ERR_FNCNOTSUPPORTED
4h
4
This function is not supported by the hardware version.
ERR_BRDREMAP
5h
5
The board index remap table in the registry is wrong. Either delete this table or check it craefully for double
values.
values.
ERR_KERNELVERSION
6h
6
The version of the kernel driver is not matching the version of the DLL. Please do a complete reinstallation of
the hardware driver. This error normally only occurs if someone copies the dll manually to the system direc-
tory.
the hardware driver. This error normally only occurs if someone copies the dll manually to the system direc-
tory.
ERR_HWDRVVERSION
7h
7
The hardware needs a newer driver version to run properly. Please install the driver that was delivered
together with the board.
together with the board.
ERR_LASTERR
10h
16
Old Error waiting to be read. Please read the full error information before proceeding. The driver is locked
until the error information has been read.
until the error information has been read.
ERR_ABORT
20h
32
Abort of wait function. This return value just tells that the function has been aborted from another thread.
ERR_BOARDLOCKED
30h
48
Access to the driver already locked by another program. Stop the other program before starting this one.
Only one program can access the driver at the time.
Only one program can access the driver at the time.
ERR_REG
100h
256
The register is not valid for this type of board.
ERR_VALUE
101h
257
The value for this register is not in a valid range. The allowed values and ranges are listed in the board spe-
cific documentation.
cific documentation.
ERR_FEATURE
102h
258
Feature (option) is not installed on this board. It’s not possible to access this feature if it’s not installed.
ERR_SEQUENCE
103h
259
Channel sequence is not allowed.
ERR_READABORT
104h
260
Data read is not allowed after aborting the data acquisition.
ERR_NOACCESS
105h
261
Access to this register denied. No access for user allowed.
ERR_POWERDOWN
106h
262
Not allowed if powerdown mode is activated.
ERR_TIMEOUT
107h
263
A timeout occured while waiting for an interrupt. Why this happens depends on the application. Please
check whether the timeout value is programmed too small.
check whether the timeout value is programmed too small.
ERR_CHANNEL
110h
272
The channel number may not be accessed on the board: Either it is not a valid channel number or the chan-
nel is not accessible due to the actual setup (e.g. Only channel 0 is accessible in interlace mode)
nel is not accessible due to the actual setup (e.g. Only channel 0 is accessible in interlace mode)
ERR_RUNNING
120h
288
The board is still running, this function is not available now or this register is not accessible now.
ERR_ADJUST
130h
304
Automatic adjustion has reported an error. Please check the boards inputs.
ERR_NOPCI
200h
512
No PCI BIOS is found on the system.
ERR_PCIVERSION
201h
513
The PCI bus has the wrong version. SPECTRUM PCI boards require PCI revision 2.1 or higher.
ERR_PCINOBOARDS
202h
514
No SPECTRUM PCI boards found. If you have a PCI board in your system please check whether it is cor-
rectly plug into the slot connector and whether you have the latest driver version.
rectly plug into the slot connector and whether you have the latest driver version.
ERR_PCICHECKSUM
203h
515
The checksum of the board information has failed. This could be a critical hardware failure. Restart the sys-
tem and check the connection of the board in the slot.
tem and check the connection of the board in the slot.
ERR_DMALOCKED
204h
516
DMA buffer not available now.
ERR_MEMALLOC
205h
517
Internal memory allocation failed. Please restart the system and be sure that there is enough free memory.
ERR_FIFOBUFOVERRUN
300h
768
Driver buffer overrun in FIFO mode. The hardware and the driver have been fast enough but the application
software didn’t manage to transfer the buffers in time.
software didn’t manage to transfer the buffers in time.
ERR_FIFOHWOVERRUN
301h
769
Hardware buffer overrun in FIFO mode. The hardware transfer and the driver has not been fast enough.
Please check the system for bottlenecks and make sure that the driver thread has enough time to transfer
data.
Please check the system for bottlenecks and make sure that the driver thread has enough time to transfer
data.
ERR_FIFOFINISHED
302h
770
FIFO transfer has been finished, programmed number of buffers has been transferred.
ERR_FIFOSETUP
309h
777
FIFO setup not possible, transfer rate to high (max 250 MB/s).
ERR_TIMESTAMP_SYNC
310h
784
Synchronisation to external timestamp reference clock failed. At initialisation is checked wether there is a
clock edge present at the input.
clock edge present at the input.
ERR_STARHUB
320h
800
The autorouting function of the star-hub initialisation has failed. Please check whether all cables are mounted
correctly.
correctly.