Roland BR-600 用户手册
61
Re-recording Only a Mistake (Punch-in/out)
Re
v0.10
v0.10
Section 1
It can be difficult sometimes to punch in and out with the
[REC] button when both playing an instrument and
recording by yourself. In such situations, you may find it
convenient to connect a sold separately foot switch (such as
a BOSS FS-5U or Roland DP-2) and use the foot switch to
punch in and out.
[REC] button when both playing an instrument and
recording by yourself. In such situations, you may find it
convenient to connect a sold separately foot switch (such as
a BOSS FS-5U or Roland DP-2) and use the foot switch to
punch in and out.
In order to use a foot switch
When you are using a sold separately foot switch to punch
in and out, connect the foot switch to the FOOT SW jack on
the BR-600 and change the function of the FOOT SW jack by
following the procedure given below.
in and out, connect the foot switch to the FOOT SW jack on
the BR-600 and change the function of the FOOT SW jack by
following the procedure given below.
1
Confirm that [PAD] is not lit, then press [UTILITY].
2
Press CURSOR [
] [
] to move the cursor to
“SYS,” and press [ENTER].
fig.01-190
3
Press CURSOR [
] [
] and select “Foot SW.”
fig.01-200
4
Turn the TIME/VALUE dial and select “PUNCH”
(PUNCH IN/OUT).
(PUNCH IN/OUT).
5
Press [UTILITY] (or press [EXIT] repeatedly) to return
to the Play screen.
to the Play screen.
* During updating, “Keep power on!” appears in the upper
line of the display, while the lower line shows what is being
processed.
processed.
Automatically punching in and out at predetermined
locations (or times) in the song is referred to as “auto
punching in/out.”
locations (or times) in the song is referred to as “auto
punching in/out.”
When you want to punch in and out at accurate times or
when you want to concentrate on playing rather than
punching in and out manually, the auto punch in/out
function is very useful.
when you want to concentrate on playing rather than
punching in and out manually, the auto punch in/out
function is very useful.
* When using auto punch-in/out, you need to allow for an
interval of at least one second between the punch-in and
punch-out points.
punch-out points.
Before you begin recording, you must register the locations
at which punch-in and punch-out will occur automatically.
at which punch-in and punch-out will occur automatically.
1
Register the location where you want to punch in.
Move the location where you want to punch in and
press AUTO PUNCH [IN] to register that location for
automatic punch in.
press AUTO PUNCH [IN] to register that location for
automatic punch in.
At this time, the AUTO PUNCH [IN] lights, telling you
that the punch-in position is registered.
that the punch-in position is registered.
fig.01-210
* If the AUTO PUNCH [IN] is lit, you will automatically
move to the registered punch-in time when this button is
pressed.
pressed.
2
Register the location where you want to punch out.
Move the location where you want to punch out and
press AUTO PUNCH [OUT] to register that location
for automatic punch out.
press AUTO PUNCH [OUT] to register that location
for automatic punch out.
At this time, the AUTO PUNCH [OUT] lights, telling
you that the punch-out position is registered.
you that the punch-out position is registered.
fig.01-220
* If the AUTO PUNCH [OUT] is lit, you will automatically
move to the registered punch-out time when this button is
pressed.
pressed.
■
Manually punching in and
out using a foot switch
out using a foot switch
In operating the foot switch during playback of a song
(manual patch in and out), press the foot switch once to
punch in, then press it again to punch out.
(manual patch in and out), press the foot switch once to
punch in, then press it again to punch out.
Auto Punching In and Out
■
Specifying the area for auto
punching in/out
punching in/out
BR600_e2 61 ページ ２００６年４月１７日 月曜日 午前９時３分