Schneider Electric ALTIVAR 58 TRX 用户手册
Altivar
®
58 TRX AC Drives
Description of Type FVC Control Terminals
©
2000–2003 Schneider Electric All Rights Reserved
22
09/2003
DESCRIPTION OF ATV58 TYPE FVC CONTROL TERMINALS
The ATV58 Type FVC control terminals are shown below. The location of the control terminal strip varies
from model to model. See page 18.
from model to model. See page 18.
The control terminal strip contains four pull-apart terminal blocks, one for the relay outputs and three for
the low-level inputs and outputs. The S terminals are used to connect shield wires of multi-conductor
control cables for the low level inputs, outputs, and encoder. Maximum wire size for all control terminals
is 16 AWG (1.5 mm
the low-level inputs and outputs. The S terminals are used to connect shield wires of multi-conductor
control cables for the low level inputs, outputs, and encoder. Maximum wire size for all control terminals
is 16 AWG (1.5 mm
2
). Tightening torque is 2.2 lb-in (0.25 N•m). The characteristics of the control
terminals are shown in the table below.
Function of Terminals
Terminals
Function
Electrical Characteristics
R1A
R1B
R1C
R1B
R1C
R1A to R1C is a N.O.
contact. When the drive
controller is powered with no
fault, the contact is closed.
contact. When the drive
controller is powered with no
fault, the contact is closed.
R1B to R1C is a N.C.
contact. When the drive
controller is powered with no
fault, the contact is open.
contact. When the drive
controller is powered with no
fault, the contact is open.
• Minimum switching capacity: 10mA for 24 Vdc.
• Maximum switching capacity on inductive load: 1.5 A for 250 V Vac (cos
• Maximum switching capacity on inductive load: 1.5 A for 250 V Vac (cos
ϕ
0.4) and
30 Vdc (L/R 7 ms).
• Maximum response time: 20 ms.
R2A
R2C
R2C
N.O. contact of R2
programmable relay
programmable relay
COM
Common for logic and
analog inputs
analog inputs
AI1A
AI1B
AI1B
Differential analog input
• ± 10V, impedance 40 k
Ω
in differential mode, 20 k
Ω
in common mode.
• Maximum permissible voltage ± 30 V.
• Resolution 11 bits + sign.
• Accuracy ± 0.5% of maximum value.
• Linearity ± 0.2% of maximum value.
• Sampling time 2 ms maximum.
• Resolution 11 bits + sign.
• Accuracy ± 0.5% of maximum value.
• Linearity ± 0.2% of maximum value.
• Sampling time 2 ms maximum.
+ 10
Supply for reference
potentiometer (1 to 10 k
potentiometer (1 to 10 k
Ω)
• Voltage + 10 V (-0 + 10%) 10 mA maximum protected against short circuits and
overloads.
AI2
Programmable analog input
• Input 0-20 MA, programmable for X-Y mA by configuring X and Y (0 to 20).
• Impedance 100
• Impedance 100
Ω.
• Maximum permissible current 50 mA.
• Resolution 0.02 mA.
• Accuracy ± 1% of maximum value.
• Linearity ± 5% of maximum value.
• Sampling time 2 ms maximum.
• Resolution 0.02 mA.
• Accuracy ± 1% of maximum value.
• Linearity ± 5% of maximum value.
• Sampling time 2 ms maximum.
AO1
Programmable analog
output
output
• Output 0-20 MA, programmable for X-Y mA by configuring X and Y (0 to 20).
• Load impedance 500
• Load impedance 500
Ω
maximum.
• Resolution 0.02 mA.
• Accuracy ± 1% of maximum value.
• Linearity ± 5% of maximum value.
• Sampling time 2 ms maximum.
• Accuracy ± 1% of maximum value.
• Linearity ± 5% of maximum value.
• Sampling time 2 ms maximum.
LI1
LI2
LI3
LI4
LI2
LI3
LI4
Programmable logic inputs
function depends on
configuration
function depends on
configuration
• Impedance 3.5 k
Ω
.
• Power supply + 24 V (maximum 30 V).
• State 0 if < 5 V, state 1 if > 11V.
• Sampling time 2 ms maximum.
• State 0 if < 5 V, state 1 if > 11V.
• Sampling time 2 ms maximum.
+ 24
Power supply for logic inputs
• Voltage + 24 V protected against short circuits and overload, minimum 18 V,
maximum 30 V.
• Maximum current 120 mA.
A
A-
B
B-
A-
B
B-
Encoder inputs
• For Incremental optical encoder with RS422-compatible differential outputs.
• Impedance 330
• Impedance 330
Ω
.
• Maximum 5000 pulses/rev., minimum 100 pulses/rev.
• Maximum frequency 200 kHZ at high speed (HSP).
• Maximum frequency 200 kHZ at high speed (HSP).
+ 5 V
0 V
0 V
Power supply for encoder
• Voltage 5 V (maximum 5.5 V) protected against short circuits and overloads.
• Maximum current 200 mA.
• Maximum current 200 mA.
R1A
R1B
R1C
R2A
R2C
COM
AI 1A
AI1B
+ 10
AI 2
A01
A
A-
B
B-
5 V
0 V
LI 1
LI 2
LI 3
LI 4
+ 24
Shielding connection screw for
analog I/O and logic inputs
analog I/O and logic inputs
Shielding connection
screw for encoder
cable
screw for encoder
cable
S
S
ar
ra
ng
e o
f t
e
rm
s cop
y.
e
ps