RF-Link Technology NL6000 用户手册
RF Neulink
NL6000 User Guide
25
5.6.5. Carrier Sense Multiple Access
If a unit s transmit and receive frequencies are the same, it may be helpful to
enable Carrier Sense Multiple Access (CSMA). This option does not allow
transmission of a packet until the channel is free of contention.
enable Carrier Sense Multiple Access (CSMA). This option does not allow
transmission of a packet until the channel is free of contention.
5.7.
Serial Connection to an I/O Device
5.7.1. Basic Serial Parameters
The NL6000 can receive data strings from a variety of I/O devices through its
RS232 serial port. Configure the NL6000 serial port parameters based upon
how the I/O device will send data to the unit. The following is a list of the basic
serial parameters you must configure:
RS232 serial port. Configure the NL6000 serial port parameters based upon
how the I/O device will send data to the unit. The following is a list of the basic
serial parameters you must configure:
•
Baud rate
This parameter is the data rate between the I/O device and
the NL6000 modem. Set the baud rate to the rate of the I/O device.
•
Data bits
This parameter is the number of bits the I/O device sends in a
byte. The options available are 7 or 8. The NL6000 does not use parity
bits.
bits.
•
Stop bits
This parameter is the number of bits used for the end of a
byte. The options available are 1 or 2.
•
Transmit Character Timeout
The NL6000 transmits a data packet on
the radio channel when there is a timeout on the serial port equal to this
value or when the amount of data in the input buffer is equal to the
Maximum Packet Size.
value or when the amount of data in the input buffer is equal to the
Maximum Packet Size.
5.7.2. Flow Control
Prior to configuration of the NL6000, determine if you want to use flow control
to prevent the serial device or modem from overflowing its buffer. If flow
control is desired, two types are available
to prevent the serial device or modem from overflowing its buffer. If flow
control is desired, two types are available
RTS/CTS and XON/XOFF. With
RTS/CTS, the modem monitors the RTS signal to determine when to send
data to the serial device. In addition, the modem asserts CTS when the
modem is ready to accept data from the serial device. RTS/CTS is the
preferred method of flow control, but it requires separate lines for RTS and
CTS. If you cannot use hardware flow control, you may use the XON/XOFF
software option for flow control. This option may only be used for ASCII data
and requires the use of special characters to identify when it is OK to send/
receive data to/from the serial device.
data to the serial device. In addition, the modem asserts CTS when the
modem is ready to accept data from the serial device. RTS/CTS is the
preferred method of flow control, but it requires separate lines for RTS and
CTS. If you cannot use hardware flow control, you may use the XON/XOFF
software option for flow control. This option may only be used for ASCII data
and requires the use of special characters to identify when it is OK to send/
receive data to/from the serial device.
5.7.3. DCD Mode
The DCD Mode parameter identifies how the I/O device interprets the current
state of the modem using the DCD line between the device and the modem. If
the mode is set to Enable, the modem asserts the DCD line when it is
receiving data over-the-air. If the mode is set to Disable, the modem asserts
the line when it is in a normal operating state and negates the line when it is in
state of the modem using the DCD line between the device and the modem. If
the mode is set to Enable, the modem asserts the DCD line when it is
receiving data over-the-air. If the mode is set to Disable, the modem asserts
the line when it is in a normal operating state and negates the line when it is in