Pelco Computer Keyboard KBD4000 用户手册
Pelco Manual C1921M-G (1/04)
29
PROGRAMMING A PRESET
1.
Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT key
lights.
lights.
When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in the
Advanced System Setup menu must be set to TRACK MAIN (refer to the
Advanced System Setup menu must be set to TRACK MAIN (refer to the
Advanced
System Setup
section).
2.
Select the camera.
Addressing by Multiplexer (Switch 7 OFF)
a.
a.
On the number pad, enter the multiplexer’s address number (1-16 if the keyboard
is connected to a multiplexer; 1-8 if the keyboard is connected to a server), and
then press the UNIT key. The LED displays the address.
is connected to a multiplexer; 1-8 if the keyboard is connected to a server), and
then press the UNIT key. The LED displays the address.
b.
On the number pad, enter the camera’s number (1-16), and then press the CAM
key.
key.
Addressing Consecutively (Switch 7 ON)
On the number pad, enter the camera’s number, and then press the CAM key. Refer
to Table A for camera numbers.
On the number pad, enter the camera’s number, and then press the CAM key. Refer
to Table A for camera numbers.
3.
Position the camera.
4.
On the number pad, enter the preset’s number, and then hold down the PRESET key
for five seconds.
for five seconds.
PROGRAMMING A PATTERN
1.
Press the MAIN or SPOT MONITOR key. The green LED over the MAIN or SPOT key
lights.
lights.
When using the MAIN MONITOR, the SPOT MONITOR DISPLAY menu item in the
Advanced System Setup menu must be set to TRACK MAIN (refer to the
Advanced System Setup menu must be set to TRACK MAIN (refer to the
Advanced
System Setup
section).
2.
Select the camera.
Addressing by Multiplexer (Switch 7 OFF)
a.
a.
On the number pad, enter the multiplexer’s address number (1-16 if the keyboard
is connected to a multiplexer; 1-8 if the keyboard is connected to a server), and
then press the UNIT key. The LED displays the address.
is connected to a multiplexer; 1-8 if the keyboard is connected to a server), and
then press the UNIT key. The LED displays the address.
b.
On the number pad, enter the camera’s number (1-16), and then press the CAM
key.
key.
Addressing Consecutively (Switch 7 ON)
On the number pad, enter the camera’s number, and then press the CAM key. Refer
to Table A for camera numbers.
On the number pad, enter the camera’s number, and then press the CAM key. Refer
to Table A for camera numbers.
3.
On the number pad, press a number key for the pattern number. Example: If you are
programming pattern 1 press the number 1 key. Then hold down the PATTERN key
until the message PROGRAMMING PATTERN appears on the screen.
programming pattern 1 press the number 1 key. Then hold down the PATTERN key
until the message PROGRAMMING PATTERN appears on the screen.
4.
Move the camera through the pattern.
5.
To stop programming the pattern, repress the number key for the pattern followed by
the PATTERN key. Example: Press number 1 and then the PATTERN key if you are
programming pattern 1. The message PROGRAMMING PATTERN disappears.
the PATTERN key. Example: Press number 1 and then the PATTERN key if you are
programming pattern 1. The message PROGRAMMING PATTERN disappears.
NOTE:
The LEDs above
the camera buttons on the
multiplexer light to show
which cameras are being
displayed.
multiplexer light to show
which cameras are being
displayed.
NOTE:
Refer to your dome
or pan and tilt system
manual for information on
the number of available pat-
terns and pattern durations.
manual for information on
the number of available pat-
terns and pattern durations.
NOTE:
DIP switch number
8 must be ON for program-
ming.
ming.