Texas Instruments Serial Programming Adapter MSP430 用户手册
www.ti.com
Kit Contents, EM430Fx137RF900
Table 1-2. Individual Kit Contents, MSP-TS430xx (continued)
Target Socket
Socket Type
Supported Devices
Included Devices
Headers / Comment
Module
100-pin PZ
Eight PCB 1×25-pin headers (four
MSP-TS430PZ100B
MSP430F67xx
2 x MSP430F6733IPZ
(QFP ZIF)
male and four female
MSP-
100-pin PZ
MSP430F543x,MSP430
Eight PCB 1×25-pin headers (four
2 x MSP430F5438IPZ
TS430PZ5x100
(QFP ZIF)
BT5190IPZ
male and four female
MSP-
100-pin PZ
Eight PCB 1×25-pin headers (four
MSP430F663x, 'F563x
2 x MSP430F6638IPZ
TS430PZ100USB
(QFP ZIF)
male and four female
See the device data sheets for device specifications. Device errata can be found in the respective device
product folder on the web provided as a PDF document. Depending on the device, errata may also be
found in the device bug database at
product folder on the web provided as a PDF document. Depending on the device, errata may also be
found in the device bug database at
1.13 Kit Contents, EM430Fx137RF900
•
One READ ME FIRST document
•
One legal notice
•
One MSP430 CD-ROM
•
Two target socket module
MSP-EM430F5137RF900: Two EM430F5137RF900 target socket modules. This is the PCB on which
is soldered a CC430F5137 device in a 48-pin RGZ package. A 2×7-pin male connector is also present
on the PCB
MSP-EM430F6137RF900: Two EM430F6137RF900 target socket modules. This is the PCB on which
is soldered a CC430F6137 device in a 64-pin RGC package. A 2×7-pin male connector is also present
on the PCB
MSP-EM430F5137RF900: Two EM430F5137RF900 target socket modules. This is the PCB on which
is soldered a CC430F5137 device in a 48-pin RGZ package. A 2×7-pin male connector is also present
on the PCB
MSP-EM430F6137RF900: Two EM430F6137RF900 target socket modules. This is the PCB on which
is soldered a CC430F6137 device in a 64-pin RGC package. A 2×7-pin male connector is also present
on the PCB
•
Two CC430EM battery packs
•
Four AAA batteries
•
Two 868-/915-MHz antennas
•
Two 32.768-kHz crystals
•
18 PCB 2×4-pin headers
1.14 Hardware Installation, MSP-FET430PIF
Follow these steps to install the hardware for the MSP-FET430PIF tools:
1. Use the 25-conductor cable to connect the FET interface module to the parallel port of the PC. The
necessary driver for accessing the PC parallel port is installed automatically during CCE/CCS or IAR
Embedded Workbench installation. Note that a restart is required after the CCE/CCS or IAR
Embedded Workbench installation for the driver to become active.
Embedded Workbench installation. Note that a restart is required after the CCE/CCS or IAR
Embedded Workbench installation for the driver to become active.
2. Use the 14-conductor cable to connect the parallel-port debug interface module to a target board, such
as an MSP-TS430xxx target socket module. Module schematics and PCBs are shown in
19
SLAU278F – May 2009 – Revised December 2010
Get Started Now!
© 2009–2010, Texas Instruments Incorporated