Omron SYSMAC C200HW-ZW3AT2-E-V2 用户手册
3-3
Section
Connecting to a Node
25
RS-232C Port on Host Link Unit
Computer
Cable
PC (Host
Link Unit)
PC com-
munica-
tions
PC/AT
RS-232C port
RS-232C
CV500-LK201 port 1, in full-duplex mode:
XW2Z-200S (D-Sub 25-pin
↔
D-Sub 9-pin)
XW2Z-500S (D-Sub 25-pin
↔
D-Sub 9-pin)
CV500-LK201 port 2, in full-duplex mode:
XW2Z-200P (D-Sub 25-pin
↔
D-Sub 25-pin)
XW2Z-500P (D-Sub 25-pin
↔
D-Sub 25-pin)
RS-232C
port on
Host LInk
Unit for
CVM1 or
CV-series
PC
(CV500-LK
201)
port on
Host LInk
Unit for
CVM1 or
CV-series
PC
(CV500-LK
201)
Host Link
Select an appropriate cable according to the shape of the RS-232C connector
on the Host Link Unit.
on the Host Link Unit.
RS-232C Port on Serial Communications Board/Unit
Computer
Cable
PC(Serial
Communic
ations
Board/Unit)
PC com-
munica-
tions
PC/AT
RS-232C port
RS-232C
XW2Z-200S (D-Sub 25-pin
↔
D-Sub 9-pin)
XW2Z-500S (D-Sub 25-pin
↔
D-Sub 9-pin)
RS-232C
port on
Serial Com-
munications
Board
(CS1W-SC
B21/41) or
Serial Com-
munications
Unit
(CS1W-SC
U21) for
CS1-series
PC
port on
Serial Com-
munications
Board
(CS1W-SC
B21/41) or
Serial Com-
munications
Unit
(CS1W-SC
U21) for
CS1-series
PC
Host Link
3-3-2 PC Settings
Peripheral Bus
If the Controller Link Support Software is to communicate with a PC via the pe-
ripheral bus, the PC must be set to the same baud rate as the Controller Link
Support Software.
ripheral bus, the PC must be set to the same baud rate as the Controller Link
Support Software.
Note See 5-14-3 Setting PC Communications (on page 137) in 5-14 System Setup to
set the baud rate for the Controller Link Support Software.
CS1-series PCs
Connecting to Peripheral Port
When connecting to the peripheral port on the CPU Unit, set DIP switch pin 4 to
OFF, and set the baud rate for the Controller Link Support Software to the maxi-
mum value (19,200 bps). Alternatively, set DIP switch pin 4 to ON and make the
PC Setup settings for the CPU Unit using CX-Programmer. Select the peripheral
port and set the serial communications mode to peripheral bus, and make the
same communications settings as the Controller Link Support Software.
When connecting to the peripheral port on the CPU Unit, set DIP switch pin 4 to
OFF, and set the baud rate for the Controller Link Support Software to the maxi-
mum value (19,200 bps). Alternatively, set DIP switch pin 4 to ON and make the
PC Setup settings for the CPU Unit using CX-Programmer. Select the peripheral
port and set the serial communications mode to peripheral bus, and make the
same communications settings as the Controller Link Support Software.
Connecting to RS-232C Port
When connecting to the RS-232C port on the CPU Unit, set DIP switch pin 5 to
ON, and set the baud rate for the Controller Link Support Software to the maxi-
mum value (19,200 bps). Alternatively, set DIP switch pin 5 to OFF and make the
PC Setup settings for the CPU Unit using CX-Programmer. Select the RS-232C
port and set the serial communications mode to peripheral bus, and make the
same communications settings as the Controller Link Support Software.
When connecting to the RS-232C port on the CPU Unit, set DIP switch pin 5 to
ON, and set the baud rate for the Controller Link Support Software to the maxi-
mum value (19,200 bps). Alternatively, set DIP switch pin 5 to OFF and make the
PC Setup settings for the CPU Unit using CX-Programmer. Select the RS-232C
port and set the serial communications mode to peripheral bus, and make the
same communications settings as the Controller Link Support Software.