Nuvo Home Theater System NV-E6D-UK 用户手册
NOTE: the Main Unit ships with the carrier frequency DEFAULT setting of 38 KHz for all six sources.
*********************************************************************************
COMMAND: *IRSETDF<CR> Restores DEFAULT SOURCE IR carrier frequency settings (38 KHz for all six sources).
RESPONSE: Same response as for #IRSETSR<CR>
COMMAND: *IRSETDF<CR> Restores DEFAULT SOURCE IR carrier frequency settings (38 KHz for all six sources).
RESPONSE: Same response as for #IRSETSR<CR>
*********************************************************************************
COMMAND: *SxIR56SET<CR> - sets SOURCE x to 56 KHz IR repeat carrier (x is 1 to 6).
RESPONSE: Same response as for #IRSETSR<CR>
COMMAND: *SxIR56SET<CR> - sets SOURCE x to 56 KHz IR repeat carrier (x is 1 to 6).
RESPONSE: Same response as for #IRSETSR<CR>
*********************************************************************************
COMMAND: *SxIR38SET<CR> - sets SOURCE x to 38 KHz IR repeat carrier (x is 1 to 6).
RESPONSE: Same response as for #IRSETSR<CR>
COMMAND: *SxIR38SET<CR> - sets SOURCE x to 38 KHz IR repeat carrier (x is 1 to 6).
RESPONSE: Same response as for #IRSETSR<CR>
*********************************************************************************
COMMAND/RESPONSE DESCRIPTIONS.
NOTE zone number field xx should ALWAYS include a lead zero (“0”) for zone numbers less than 10.
NOTE zone number field xx should ALWAYS include a lead zero (“0”) for zone numbers less than 10.
COMMAND: *ZxxCONSR<CR> - Connect STATUS REQUEST where xx is zone # from 1 to
12.
RESPONSE: #ZxxPWRppp,SRCs,GRPt,VOL-yy,Pzzz<CR>
-ppp = “ON” (2 characters)
or “OFF” (3 characters)
The remaining fields are not included in the response if ppp is “OFF”:
-s = SOURCE NUMBER 1 to 6
-q = 0 if SOURCE GROUP is ON 1if SOURCE GROUP is OFF
-yy = level below max in dB: -00 to -78 dB (include lead 0 for all single-digit
values)
-yy = “MT” if in MUTE state
-yy = “XM” if external MUTE is being held
-q = 0 if SOURCE GROUP is ON 1if SOURCE GROUP is OFF
-yy = level below max in dB: -00 to -78 dB (include lead 0 for all single-digit
values)
-yy = “MT” if in MUTE state
-yy = “XM” if external MUTE is being held
active
-zzz = “MST” if this zone is PARTY MASTER
-zzz = “SLV” if this zone is SLAVED to a
-zzz = “SLV” if this zone is SLAVED to a
PARTY MASTER in another zone
-zzz = “OFF” if this zone is under LOCAL CONTROL only (either there is no
party master, or this zone has been manually
overridden)
overridden)
This response will also be issued in response to pressing the ON/OFF, VOLUME, or SOURCE
keys on a KEYPAD. NOTE the response will be issued if a SOURCE key is pressed on a
zone that is powered OFF even though the key press has no effect on the system. It will be
output at every increment during a volume ramp initiated by HOLDING a VOLUME UP or
VOLUME DOWN key on a keypad. It will also be issued at every increment of a volume
ramp commanded by the *ZxxVOL+<CR> and *ZxxVOL-<CR> commands (see below).
keys on a KEYPAD. NOTE the response will be issued if a SOURCE key is pressed on a
zone that is powered OFF even though the key press has no effect on the system. It will be
output at every increment during a volume ramp initiated by HOLDING a VOLUME UP or
VOLUME DOWN key on a keypad. It will also be issued at every increment of a volume
ramp commanded by the *ZxxVOL+<CR> and *ZxxVOL-<CR> commands (see below).
The MUTE value will be asserted if a *ZxMTON<CR> command has been received, OR if the
volume is run all the way to the lowest possible point (volume off). An active EXTERNAL
volume is run all the way to the lowest possible point (volume off). An active EXTERNAL
24