NEC 2400 PX 用户手册
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
NDA-24297, Issue 1
Page 359
Forced Account Code
F-7
F-7
Forced Account Code
General Description
This feature is a variation of the ACCOUNT CODE [A-18] feature, which makes it mandatory to enter an
ACCOUNT CODE (up to 10 digits) for all outgoing calls. The account code must be dialed before dialing the
outgoing number. Calls are processed only when the dialed account code is valid.
ACCOUNT CODE (up to 10 digits) for all outgoing calls. The account code must be dialed before dialing the
outgoing number. Calls are processed only when the dialed account code is valid.
The FORCED ACCOUNT CODE can be masked on the D
term
display if necessary using the AUTHORIZATION
CODE DISPLAY ELIMINATION [A-99].
Operating Procedure
When dialing an outgoing call
1.
Lift the handset; receive dial tone.
2.
Enter the access code; receive service set tone.
3.
Enter the FORCED ACCOUNT CODE (up to 10 digits); receive dial tone.
4.
Dial the desired number.
Note:
The access code for FORCED ACCOUNT CODE will be a maximum of 3 digits.
Service Conditions
1.
The maximum number of digits per ACCOUNT CODE [A-18] is ten.
2.
If both FORCED ACCOUNT CODE and AUTHORIZATION CODE [A-20] are provided in the system,
the maximum number of codes are 20,000.
the maximum number of codes are 20,000.
Note
Note:
Capacity depends on system configuration.
These specifications are based on the digits being assigned as follows:
1st digit:
1st digit:
A (when A equals a unique digit from 0 - 9)
2nd digit:
B - C (when b, c equal any two unique digits from 0 - 9)
3rd digit:
D-E (when d, e equal any two unique digits from 0 - 9)
4th digit:
F-G-H (when f, g, h equal any three unique digits from 0 - 9)
5th - 8th digits:
Any combination 0 - 9
9th & 10th digits:
Assigned using the checksum. These are for validation purposes only.
Note:
See ETI: 082 for details on AUTHORIZATION CODE/FORCED ACCOUNT CODE [F-7] assignment.
3.
AUTHORIZATION CODE [A-20] and FORCED ACCOUNT CODE cannot be provided simultaneously
for the same TENANT SERVICE [T-12] group. System data programming determines whether
AUTHORIZATION CODE [A-20] or FORCED ACCOUNT CODE is provided for each Tenant.
for the same TENANT SERVICE [T-12] group. System data programming determines whether
AUTHORIZATION CODE [A-20] or FORCED ACCOUNT CODE is provided for each Tenant.
4.
Stations are assigned this feature according to CLASS OF SERVICE - INDIVIDUAL [C-15]
programming in system data.
programming in system data.
5.
An assigned FORCED ACCOUNT CODE can be used for REMOTE ACCESS TO SYSTEM [R-2].
6.
FORCED ACCOUNT CODE can be recorded on SMDR [S-10] for INWATS and central office incoming
calls, when used in conjunction with REMOTE ACCESS TO SYSTEM [R-2]. A maximum of 10 digits
can be registered as an account code for SMDR purposes.
calls, when used in conjunction with REMOTE ACCESS TO SYSTEM [R-2]. A maximum of 10 digits
can be registered as an account code for SMDR purposes.
7.
When used in conjunction with REMOTE ACCESS TO SYSTEM [R-2], FORCED ACCOUNT CODE
cannot be registered on SMDR if the incoming calls are terminated to stations via night service or DID
[D-8].
cannot be registered on SMDR if the incoming calls are terminated to stations via night service or DID
[D-8].
8.
FORCED ACCOUNT CODE can be output in the SMDR [S-10] record for outgoing calls from a station
handled with OUTGOING TRUNK QUEUING [O-2].
handled with OUTGOING TRUNK QUEUING [O-2].