Honeywell Garage Door Opener 5828/5828V 用户手册

下载
页码 4
 
- 2 - 
3.  Press 
✱ READY  to accept your entry. The keypad 
will display the system status. 
MEMO/MESSAGE CENTER (5828V only) 
Recording and playing back messages 
The keystrokes required for message recording and 
playback are as shown in the table below. 
In this table, read the + sign as “followed by.” 
Example: # + 1 would be read as the [#] key followed by 
the [1] key. 
MESSAGE CENTER (LYNX) 
TO: PRESS: 
Record a message: 
# + 1 
Stop recording before end of 20 seconds: 
Playback a message: 
# + 3 
Adjust message playback volume: 
# + 2 + 3
↑ or 6↓ 
Mute system status announcements: 
# + 2 + 1 
Restore system status announcements: 
# + 2 + 3
↑ or 6↓ 
MESSAGE CENTER (VISTA) 
TO: PRESS: 
Record a message: 
# + 0 + 1 
Stop recording before end of 20 seconds: 
Playback a message: 
# + 0 + 3 
Adjust message playback volume: 
# + 0 + 2 + 3
↑ or 6↓ 
Mute system status announcements: 
# + 0 + 2 + 1 
Restore system status announcements: 
# + 0 + 2 + 3
↑ or 6↓ 
New message indication: If powered by battery, the 
Message LED will only blink when you activate the 
keypad by requesting status.  If powered by AC, the 
Message LED will blink continuously.  Once the 
message is played back, the LED will no longer blink. 
NOTE: If using a LYNX control, and the word 
“MESSAGE” is announced at the 5828V keypad, it 
means that there is a message waiting at the control 
panel, 
which can only be retrieved using the LYNX 
keypad. 
MESSAGE CENTER NOTES  
•  Allow any alarm system status annunciation to 
complete before starting to record your message. 
•  Messages up to 20-seconds long may be recorded and 
played back at any time.  
•  When messages are first recorded, the red message 
LED will continuously flash to show that a new 
message is contained in the message center memory. 
Once that message is played back, the LED will no 
longer flash but the message is retained until a new 
message is recorded over it. 
•  A status announcement will interrupt the recording 
or playback of a message. If this happens, begin 
recording or playing the message back again. 
If you Mute system status announcements for any 
reason, you must Restore system status 
announcements 
by pressing the keys indicated in the 
“MESSAGE CENTER” table (above) in order to hear 
them again. They will not restore on their own.  
•  Recording a message or playing back a stored 
message is NOT affected by muting. 
•  If you adjust the volume (3↑ or 6↓) when you play 
back a message, and still want system status 
announcements to be muted, you must again mute 
system status announcements (# + 2 + 1 for Lynx 
panels or # + 0 + 2 + 1 for VISTA panels). 
HOW TO REPLACE THE BATTERIES 
1.  If the keypad is AC powered, unplug the AC 
transformer from the wall outlet. 
2.  If the keypad is not wall mounted advance to step 3. 
If the keypad is wall mounted, perform the 
following:  
Grasp the keypad firmly. Lift straight up (about 1/4 
inch) and then out, to separate the keypad from the 
mounting plate. This exposes the covered battery 
compartment on the backside of the keypad. 
3.  Rest the inverted keypad on a non-abrasive surface 
and remove the battery compartment cover.  Remove 
the old batteries and properly discard. 
4.  Replace the old batteries with 3 AA, 1.5 Volt, 
Alkaline batteries (ADEMCO part number 468 or 
equivalent).  Always replace all three batteries at 
once to ensure normal operation of the keypad over 
the anticipated battery lifetime. Make sure that 
battery positive (+) and negative (–) terminals are 
properly oriented with the battery spring clip 
connections.  Refer to battery placement graphic 
below.  
batt_case-001-V0
AA BATTERY
AA BATTERY
AA BATTERY
 
Battery Compartment 
5.  Replace the battery cover. 
6.  If the keypad is not wall mounted advance to step 7. 
If the keypad is wall mounted, perform the 
following:  
Reattach the keypad to its mounting plate by 
aligning the four mounting holes in the keypad case 
back with the four mounting clips on the mounting 
plate. Lower the keypad onto the clips. 
7.  If the keypad is AC powered, plug the AC 
transformer into the wall outlet. 
8.  Activate the keypad by pressing any numbered key 
until it beeps. 
9.  Enter the following twice: your 4-digit security code 
+  1 OFF , to clear any trouble condition displayed.