Hitachi 3300MFP 用户手册
EN
Interpreting the configuration page 213
52
BAD BOOTP/DHCP REPLY
BAD BOOTP/DHCP REPLY
An error was detected in the BOOTP or DHCP reply that the print server
received. The reply either had insufficient data in the UDP datagram to
contain the minimum BOOTP/DHCP header of 236 bytes, had an operation
field that was not BOOTPREPLY(0X02), had a header field that did not
match the print server’s hardware address, or had a UDP source port that
was not the BOOTP/DHCP server port (67/udp).
received. The reply either had insufficient data in the UDP datagram to
contain the minimum BOOTP/DHCP header of 236 bytes, had an operation
field that was not BOOTPREPLY(0X02), had a header field that did not
match the print server’s hardware address, or had a UDP source port that
was not the BOOTP/DHCP server port (67/udp).
53
BAD BOOTP TAG SIZE
BAD BOOTP TAG SIZE
The tagsize in a vendor-specific field in the BOOTP reply is either 0, or
greater than the remaining number of unprocessed bytes in the
vendor-specified area.
greater than the remaining number of unprocessed bytes in the
vendor-specified area.
54
BOOTP/RARP IN PROGRESS
BOOTP/RARP IN PROGRESS
The print server is currently in the process of obtaining its basic IP
configuration information through BOOTP/RARP.
configuration information through BOOTP/RARP.
55
BOOTP/DHCP IN PROGRESS
BOOTP/DHCP IN PROGRESS
The print server is currently in the process of obtaining its basic IP
configuration information through BOOTP/DHCP, and has not detected any
errors.
configuration information through BOOTP/DHCP, and has not detected any
errors.
56
DHCP NAK
DHCP NAK
The print server received a negative acknowledgment message from the
DHCP server in response to a configuration request.
DHCP server in response to a configuration request.
57
UNABLE TO CONNECT DHCP
SVR
UNABLE TO CONNECT DHCP
SVR
The print server had received IP parameters from a DHCP server, but
communication with the DHCP server has been lost. Check status of the
DHCP server.
communication with the DHCP server has been lost. Check status of the
DHCP server.
If an infinite lease was assigned, the print server will use the IP address of
the most recent DHCP server used, but operation may be degraded until a
DHCP server responds.
the most recent DHCP server used, but operation may be degraded until a
DHCP server responds.
58
POSTSCRIPT MODE NOT
SELECTED
POSTSCRIPT MODE NOT
SELECTED
The printer does not support AppleTalk or AppleTalk extensions.
59
INCOMPLETE F/W - MUST
DOWNLOAD
INCOMPLETE F/W - MUST
DOWNLOAD
Firmware download message. Currently downloading firmware to the print
server, or the download did not complete properly.
server, or the download did not complete properly.
5A
TURN PRINTER OFF/ON
TURN PRINTER OFF/ON
Firmware download message. Download of firmware is complete. Power
cycle the print server.
cycle the print server.
83 DISCONNECTING FROM
SERVER
SERVER
The server has been shut down because of a configuration change or reset
request. This message automatically clears after a few seconds, unless the
printer is off line, is in an error state, or is servicing another I/O port or
another network protocol.
request. This message automatically clears after a few seconds, unless the
printer is off line, is in an error state, or is servicing another I/O port or
another network protocol.
F1
TRYING TO CONNECT TO
SERVER
TRYING TO CONNECT TO
SERVER
The print server is trying to connect to the NetWare server(s). This is a
normal message. Wait until either the connection is established or another
status message appears.
normal message. Wait until either the connection is established or another
status message appears.
Error Code and Message Description