Fostex X-34 用户手册
14
Model X-34 Owner’s Manual
Basic Recording - 2 (Recording with the rear panel MIC IN jack)
This section describes how to record a vocal on track 1 by plugging a microphone into the rear panel MIC IN jack 1/3.
* Before proceeding to the next step, remember to reset the X-34 to its “initial settings.” (See page 9.)
Also, make sure that the Track Down indicator is turned off.
0
0
0
LINE OUT
R
L
MONITOR OUT
R
L
AUX RTN
R
L/MONO
AUX SEND
2/4
1/3
MIC IN
TRIM 2/4
TRIM 1/3
RESET
–
+
WIDE PITCH
4
3
2
1
R
L
FIX
NORMAL
POWER
REC
NR
-
+
10
5
0
3
6
-
10
5
0
3
+
6
PAUSE
STOP
FF
REC
PLAY
REW
X-34
multitracker
DOLBY B NR
10
0
10
0
MONITOR
AUX RTN
MON MIX
AUX
+
-
0
+
-
0
R
L
10
0
+
-
0
+
-
0
R
L
10
0
+
-
0
+
-
0
R
L
10
0
+
-
0
+
-
0
R
L
10
0
AUX
EQ HI
EQ LO
MON MIX/
PAN
1
2
3
4
1
2
3
4
1
2
3
4
REC TRK
REC TRK
REC TRK
4
3
2
REC TRK
1
2
3
4
1
LINE IN/INSERT
1
2
3
4
MASTER
Down
Track
Bounce
Auto
11
7
12
2
10
9
6
5
6
4
8
3
1
9
Monitor speakers
Headphones
The MON MIX indicator lights up.
1. Plug a mic into the rear panel MIC IN jack 1/3
(1/4" or XLR).
2. Make sure that the Track Down indicator is
turned off.
<Note>
When Track Down is “ON” , the REC TRK switches are
disabled.
disabled.
3. Switch ON the Dolby B noise reduction switch.
4. If this is a new song, load a cassette in the
transport and advance the tape to recording
start position as previously described.
start position as previously described.
5. Reset the counter to [000] by pressing the
RESET button.
6. Place track 1 in REC READY mode by pressing
REC TRK switch 1.
Record track indicator 1 lights up in red.
The signal from MIC IN jack 1/3 is also routed to
channel 3.
The signal from MIC IN jack 1/3 is also routed to
channel 3.
If you also select track 3 by pressing the REC TRK
switch on channel 3, the same signal can be recorded
to tracks 1 and 3.
switch on channel 3, the same signal can be recorded
to tracks 1 and 3.
7. Raise the channel 1 input/playback level
fader to the position shown right.
8. Adjust the recording level with the Trim
1 / 3 k n o b w h i l e t a l k i n g i n t o t h e
microphone so that segments 0 - 3 on
the level meter light up.
microphone so that segments 0 - 3 on
the level meter light up.
9. The headphone and monitor volume can
be adjusted using the MONITOR knob
and the channel 1 MON MIX/AUX knob.
and the channel 1 MON MIX/AUX knob.
10. Use the EQ knobs on channel 1 to adjust the
tone.
11. After you adjust the recording level and tone,
start recording by pressing the REC button.
(The PLAY button also depresses.)
(The PLAY button also depresses.)
1
<Note>
If the Auto Bounce button
is switched on and off
while any one REC TRK
s w i t c h i s s e t t o R E C
READY state, the selected
REC TRK switch will be
canceled. In this case,
reselect the recording
track using with the REC
TRK switch.
is switched on and off
while any one REC TRK
s w i t c h i s s e t t o R E C
READY state, the selected
REC TRK switch will be
canceled. In this case,
reselect the recording
track using with the REC
TRK switch.