Ariston Coffee and Cappuccino Maker MCKA103X 用户手册

12

When cleaning, always extract the drip tray completely.  

Important!  When extracting the drip tray, the grounds con-

tainer MUST always be emptied. If this is not done, the machine
may be clogged. 

NOTE 8: Never extract the water tank while the machine is delivering
coffee. 
If it is removed, it will not be possible to make the coffee and the ap-
pliance will display "GROUND TOO FINE ADJUST MILL !  PRESS
OK" and then "FILL TANK!".  Check the level of water in the tank and
replace in the appliance.
To turn the appliance back on, insert the water spout if not already
in place (fig. 6), then press the OK icon (B9). "HOT WATER PRESS
OK" is displayed. 
Press the OK icon (B9) within a few seconds and deliver water from
the spout for about 30 seconds.  When delivery stops, the basic
modes are displayed again. 

N.B.:  The coffee maker may request the operation to be re-

peated a number of times until the air is completely elminated from
the hydraulic circuit. 

N.B.:  if this operation is not performed correctly or if the ma-

chine is turned off, the basic modes may be displayed, although the
problem is in fact still present. 

The appliance is set by default to automatically make the following
amounts of coffee:
•

espresso

•

small cup

•

medium cup

•

large cup

•

mug

To change and memorise the amount of coffee required, for exam-
ple when making an espresso, proceed as follows:
•

Press the          icon (B5) until "ESPRESSO" is displayed.

•

Press and hold the               icon (B10) until "PROGRAM QUAN-
TITY ESPRESSO" is displayed.
At the same time, the appliance delivers coffee.

•

Press the           icon (B10) again or the OK icon to stop delivery
and memorise the new quantity of coffee. 

The appliance is now reprogrammed with the new setting and is
ready for use.
You can change the amount of coffee in the small cup, medium cup,
large cup and mug. 

N.B.:  When the         icon (B11) is pressed, double the

amount of coffee set previously with the          icon (B10) is delive-
red.   

To reset the original settings, see "Resetting default values". 

The coffee mill is preset in the factory and should not require adju-
sting. However, if after making the first few coffees you find that de-
livery is either too fast or too slow (a drop at a time), this can be
corrected by adjusting the grinding adjustment knob (fig. 14).

For slower delivery and creamier coffee, turn
one click anticlockwise (finer pre-ground
coffee).
For faster delivery (not a drop at a time), turn
one click clockwise (coarser pre-ground cof-
fee).

•

Press the        icon (B4) (fig. 7) and select the pre-ground cof-
fee function. 

•

Extract the machine by pulling it outwards using the handles
(fig. 6). 

•

Lift the central lid, place one measure of pre-ground coffee in
the funnel (fig. 19), push the appliance in then proceed as de-
scribed in the section "Making coffee using coffee beans". 
N.B.: You can make just one coffee at a time by pressing the 

icon (B10) (fig. 12).

•

After using the machine with pre-ground coffee, to go back to
making coffee using beans, deactivate the pre-ground coffee
function by pressing the 

icon (B4) (fig. 7).

NOTE 1: Never introduce pre-ground coffee when the machine is off
or it could spread through the inside of the appliance. 
NOTE 2: Never add more than 1 measure, otherwise the appliance
will not make the coffee.
NOTE 3: Use the measure provided only. 
NOTE 4: Introduce only pre-ground coffee for espresso coffee ma-
chines into the funnel.
NOTE 5: If more than one measure of pre-ground coffee is used and
the funnel clogs, push the coffee down with a knife (fig. 21) then
remove and clean the brewing unit and machine as described in the
"Cleaning the brewing unit" section. 

•

Always make sure the appliance is ready.