Ariens 946101-ST622 用户手册
GB - 13
CUTTING HEIGHT ADJUSTMENT
The standard cutting height is adjustable from
1-3/16" to 4-3/8" (3 to 11.1 cm). To raise the
cutting height, place more spacers (up to 4)
below the cutter disk. Spacers not used under
the cutter disk must be assembled above the
cutter disk. For example, if you place two
spacers under the cutter disk, the other two
spacers must be in place above the cutter
disk.
NOTE: There must always be at least one
spacer between the cutter disk and the height
guide.
1-3/16" to 4-3/8" (3 to 11.1 cm). To raise the
cutting height, place more spacers (up to 4)
below the cutter disk. Spacers not used under
the cutter disk must be assembled above the
cutter disk. For example, if you place two
spacers under the cutter disk, the other two
spacers must be in place above the cutter
disk.
NOTE: There must always be at least one
spacer between the cutter disk and the height
guide.
1. Raise the cutter head off the ground.
2. Loosen and remove capscrew, lock
2. Loosen and remove capscrew, lock
washer and washer.
3. Remove height guide and bottom spacer.
4. Remove cutter disk and any of the
4. Remove cutter disk and any of the
remaining spacers required to achieve the
desired cutting height.
desired cutting height.
5. Reinstall the cutter disk.
6. Reinstall the spacers required to achieve
6. Reinstall the spacers required to achieve
the desired cutting height.
7. Reinstall height guide on the hex shaft.
NOTE: Be sure the hex shaft and the hex hole
in the height guide are correctly aligned.
in the height guide are correctly aligned.
8. Reinstall washer, lock washer and
capscrew. Tighten securely.
NOTE: The minimum cutting height may be
lowered to 1-3/16" (3 cm) by using one spacer
below the cutter disk and installing the cutter
disk upside down on the hex shaft.
lowered to 1-3/16" (3 cm) by using one spacer
below the cutter disk and installing the cutter
disk upside down on the hex shaft.
HEIGHT GUIDE REPLACEMENT
The height guide requires periodic
replacement. When used on hard surfaces,
such as concrete, it may need to be replaced
more frequently. If height guide is damaged or
worn, it must be replaced.
replacement. When used on hard surfaces,
such as concrete, it may need to be replaced
more frequently. If height guide is damaged or
worn, it must be replaced.
1. Raise the cutter head off the ground.
2. Loosen and remove capscrew, lock
2. Loosen and remove capscrew, lock
washer and washer.
3. Remove worn height guide.
4. Install new height guide.
5. Reinstall hardware and tighten securely.
4. Install new height guide.
5. Reinstall hardware and tighten securely.
SWIVEL HEAD ADJUSTMENT
1. Stop the engine and wait for all moving
parts to stop. Disconnect the spark plug
wire and place it securely away from the
spark plug.
wire and place it securely away from the
spark plug.
2. Loosen the wing knob on the bracket at
the rear of the unit.
3. Rotate the back of the unit in the opposite
direction of the side you wish to cut with.
4. Tighten wing knob securely.
1. Hex Shaft
2. Spacers
3. Cutter Disk
4. Height Guide
5. Washer
6. Lock Washer
7. Cap Screw
2. Spacers
3. Cutter Disk
4. Height Guide
5. Washer
6. Lock Washer
7. Cap Screw
2
5
1
3
4
6
7
1 spacer = 1-3/16"
(3 cm)
2 spacers = 2-3/4"
(7 cm)
3 spacers = 3-5/8"
(9.2 cm)
4 spacers = 4-3/8"
(11.1 cm)
OX0090
2
Wing Knob
OX0070