Amana Heat Pump 10730418 用户手册
8
O
PERATING
I
NSTRUCTIONS
1. Turn on the electrical power supply to the unit.
2. Place the room thermostat selector switch in the COOL or
2. Place the room thermostat selector switch in the COOL or
HEAT position (or AUTO if available, and if automatic
changeover from cooling to heating is desired).
changeover from cooling to heating is desired).
3. Set the room thermostat to the desired temperature.
MAINTENAN
MAINTENAN
MAINTENAN
MAINTENAN
MAINTENANCE
CE
CE
CE
CE
WARNING
T
O AVOID PERSONAL INJURY OR DEATH DUE TO ELECTRICAL SHOCK,
DISCONNECT ELECTRICAL POWER BEFORE PERFORMAING ANY
MAINTENANCE.
MAINTENANCE.
R
EPLACING
O
R
C
LEANING
F
ILTER
A return air filter is not supplied with this unit; however, there must be
a means of filtering all of the return air. The filter(s) may be located in
the return air duct(s), or return air filter grille(s). Consult with your
installing dealer for the actual location of the return air filter(s) for
your unit.
Dirty filters are the most common cause of inadequate heating or
cooling performance. Filter inspection should be made at least ev-
ery two months; more often if necessary because of local conditions
and usage.
Dirty throwaway filters should be discarded and replaced with a new,
clean filter. Dirty permanent filters should be washed with water, thor-
oughly dried and sprayed with a filter adhesive before being rein-
stalled. (Filter adhesives may be found at many hardware stores.)
Permanent filters should last several years; however, should one
become torn or uncleanable, it should be replaced.
a means of filtering all of the return air. The filter(s) may be located in
the return air duct(s), or return air filter grille(s). Consult with your
installing dealer for the actual location of the return air filter(s) for
your unit.
Dirty filters are the most common cause of inadequate heating or
cooling performance. Filter inspection should be made at least ev-
ery two months; more often if necessary because of local conditions
and usage.
Dirty throwaway filters should be discarded and replaced with a new,
clean filter. Dirty permanent filters should be washed with water, thor-
oughly dried and sprayed with a filter adhesive before being rein-
stalled. (Filter adhesives may be found at many hardware stores.)
Permanent filters should last several years; however, should one
become torn or uncleanable, it should be replaced.
M
AINTAINING
C
ABINET
F
INISH
Use a fine grade automotive wax on the cabinet finish to maintain
the finish’s original high luster. This is especially important in areas
with high ultraviolet radiation.
the finish’s original high luster. This is especially important in areas
with high ultraviolet radiation.
C
LEAN
O
UTSIDE
C
OIL
(Q
UALIFIED
S
ERVICER
O
NLY
)
The coil with the outside air flowing over it should be inspected an-
nually and cleaned as frequently as necessary to keep the finned
areas free of lint, hair and debris.
nually and cleaned as frequently as necessary to keep the finned
areas free of lint, hair and debris.
C
ONDENSER
AND
E
VAPORATOR
M
OTORS
Bearings on the evaporator motor and the condenser motor are per-
manently lubricated. No additional oiling is required.
manently lubricated. No additional oiling is required.
WARNING
T
O AVOID PERSONAL INJURY OR DEATH DUE TO ELECTRICAL SHOCK, DO
NOT REMOVE ANY INTERNAL COMPARTMENT COVERS OR ATTEMPT ANY
ADJUSTMENT.
CAUTION
V
ERIFY PROPER OPERATION AFTER SERVICING.
ACCESSO
ACCESSO
ACCESSO
ACCESSO
ACCESSORIES
RIES
RIES
RIES
RIES
Horizontal Duct Covers (CHK001A)
Single Point Power Connection (SPK**A)
Roof Curb - Heat Pump (PRC06A1)
Roof Curb - Universal (PRC08A1)
Over-Under to Side by Side (PDTROU6A)
Additional accessories, as described above, can be purchased to fit
specific application needs. Accessories can be ordered by the part
numbers in the table and each accessory includes its own separate
instructions.
specific application needs. Accessories can be ordered by the part
numbers in the table and each accessory includes its own separate
instructions.
R
EPLACEMENT
P
ARTS
Refer to the description in the Parts Catalog when ordering any part.
Be sure to provide the unit model, manufacturing, and serial num-
bers with the order.
NOTE: Details for installing and wiring electric heater kits and single
point wiring kits are contained in the installation instructions for these
accessories.
Be sure to provide the unit model, manufacturing, and serial num-
bers with the order.
NOTE: Details for installing and wiring electric heater kits and single
point wiring kits are contained in the installation instructions for these
accessories.
2000-2004 Goodman Company, L.P.
Effective: May 2004