DCS Computer Hardware dCS 974 用户手册
dCS 974 User Manual
Manual for Software Version 1.0x
dCS Ltd
May 2001
Manual part no: DOC1241121A1
Page 81
Document No: OS-MA-A0124-112.1A1
Contact
dCS
on + 44 1799 531 999
email to: more@dcsltd.co.uk
(inside the UK replace + 44 with 0)
web site: www.dcsltd.co.uk
Multiple Channel Sync’ing
Multiple channel sync’ing requires more things to be in sync than two channel
work - the PLL must not be dual modulus, the DSP algorithm must load with a
constant group delay, and the frame and block syncs must agree.
work - the PLL must not be dual modulus, the DSP algorithm must load with a
constant group delay, and the frame and block syncs must agree.
The dCS 974 meets all these constraints with the addition of a syncing signal
transmitted from a master unit to subsequent slave units. To do this, it passes
information in the User Bits of the AES3 message. To slave adequately, units
must have this sync information input to the
transmitted from a master unit to subsequent slave units. To do this, it passes
information in the User Bits of the AES3 message. To slave adequately, units
must have this sync information input to the
AES Ref Loop Input
, via a sync
link. Each slave will generate a copy, based on its own timing, for transmission
to the next unit in the chain. If the
to the next unit in the chain. If the
Multi-channel Sync
option is set to
On
in the
Sample Rate Conversion
menu, any units with no user bit synchronisation
data into its
AES Ref Loop Input
will become a Master. If user bit
synchronisation information is fed in, it will become a slave. Either unit will
output synchronisation information via its
output synchronisation information via its
AES CLK Output
. A master clock
(dCS 992
) can be used as the master – if more than about 8 channels are
being used, this system is best, as it avoids any tolerance build up. Connections
are shown in the multi-channel syncing applications, starting on page
are shown in the multi-channel syncing applications, starting on page
Using the multi-channel sync mode, the timing of the data at the output of the
dCS 974 is related to the data coming in. If three dCS 974 units are used in a six
channel set up, and the data into all of them is bit sync’d from (say) a six
channel source, the outputs will be bit sync’d. If the inputs are not quite bit
aligned, then the outputs will not quite be bit aligned. If the inputs are way off in
phase but frequency locked, the outputs will be way off in phase but frequency
locked, and the timing of the block structures of the several output signals will
not be defined.
dCS 974 is related to the data coming in. If three dCS 974 units are used in a six
channel set up, and the data into all of them is bit sync’d from (say) a six
channel source, the outputs will be bit sync’d. If the inputs are not quite bit
aligned, then the outputs will not quite be bit aligned. If the inputs are way off in
phase but frequency locked, the outputs will be way off in phase but frequency
locked, and the timing of the block structures of the several output signals will
not be defined.
Sample Rate (kS/s)
Time in
input
sample
rate UI’s
Time in ns,
44.1 kS/s
input
Time in ns,
96 kS/s
input
Basic dCS 974 unit to unit
output timing alignment.
output timing alignment.
± 0.3
± 50
± 24
Input misalignment allowed,
with all inputs at the same
frequency, for block
structuring to work (no
Master Clock).
with all inputs at the same
frequency, for block
structuring to work (no
Master Clock).
± 2
± 334
± 162
Input misalignment allowed,
with all inputs at the same
frequency, with Master Clock
with all inputs at the same
frequency, with Master Clock
± 4
± 668
± 324
.
± 64
± 11338
± 5208
Table 8 – Multiple Channel Sync mode – allowable input misalignment
The scope shots below show the timing relationships between two units, using
the sync link, for various conversions. They are taken from 2 units, with scope
probes on the same point in each unit. The units are linked by a sync link.
the sync link, for various conversions. They are taken from 2 units, with scope
probes on the same point in each unit. The units are linked by a sync link.
19
version 2.0 software or higher.
20
UI = Unit Interval, see AES3 spec. There are 128 UI’s per sample in AES3.
21
Master Clock can adjust its Wordclock phases as necessary.