Black & Decker RO100 用户手册

 Safety Warnings

 

 

. Cluttered or dark areas invite accidents.

 do not operate power tools in explosive atmospheres, such as in the presence 

 Power tools create sparks which may ignite 

the dust or fumes.

 keep children and bystanders away while operating a power tool. Distractions 

 Power tool plugs must match the outlet. Never modify the plug in any way. do 

 Avoid body contact with earthed or grounded surfaces such as pipes, radiators, 

 There is an increased risk of electric shock if your body is 

 do not expose power tools to rain or wet conditions. Water entering a power tool 

 do not abuse the cord. Never use the cord for carrying, pulling or unplugging 

 When operating a power tool outdoors, use an extension cord suitable for outdoor 

 Use of a cord suitable for outdoor use reduces the risk of electric shock.

 If operating a power tool in a damp location is unavoidable, use a ground fault circuit 

 Use of a GFCI reduces the risk of electric shock.

 Stay alert, watch what you are doing and use common sense when operating a 

 A moment of inattention while operating power 

 use personal protective equipment. Always wear eye protection. Protective 

used for appropriate conditions will reduce personal injuries.

 Prevent unintentional starting. ensure the switch is in the off position before 

 Remove any adjusting key or wrench before turning the power tool on. A wrench 

 do not overreach. keep proper footing and balance at all times. This enables bet-

 dress properly. do not wear loose clothing or jewelry. keep your hair, clothing 

 Loose clothes, jewelry or long hair can be 

 If devices are provided for the connection of dust extraction and collection 

 Use of dust collection 

 PoWeR Tool uSe ANd cARe

 do not force the power tool. use the correct power tool for your application. The cor-

 do not use the power tool if the switch does not turn it on and off. Any power tool 

that cannot be controlled with the switch is dangerous and must be repaired.

 disconnect the plug from the power source and/or the battery pack from the 

 Store idle power tools out of the reach of children and do not allow persons 

 Maintain power tools. check for misalignment or binding of moving parts, 

 keep cutting tools sharp and clean. Properly maintained cutting tools with sharp 

 use the power tool, accessories and tool bits, etc. in accordance with these 

 Use of the power tool for operations different from those intended could 

 ........................ earthing terminal

 

 

CAT. NO.  RO100                     FORM NO. 90590043                         Printed in China                   OCT. 2012

• Never operate the sander without a recommended sanding disc properly installed

on the hook and loop base.

• The hook and loop pad and white pad brake disk are replaceable parts. If they

become worn, return the unit to a local service center for repair.

• Do not push down—let the sander do the work.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO

Y PÓLIZA DE GARANTÍA. AdveRTeNcIA:  LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

•  AlWAyS WeAR eye PRoTecTIoN.

•  Clean your tool out periodically.

If you are using your sander as a random orbit polisher and elect to use draw

string bonnets, be sure to tuck the loose ends of the string securely under the bonnet after

tying the knot. Failure to do so may cause serious injury. Check often to assure string ends

remain tucked under bonnet.

 

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

 

• lead from lead-based paints,

 

• crystalline silica from bricks and cement and other masonry products, and

 

• arsenic and chromium from chemically-treated lumber. (CCA)

 Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter

out microscopic particles.

•  Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, 

Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

When using an extension cord, be sure to use one heavy enough to carry the current your

product will draw. An undersized cord will cause a drop in line voltage resulting in loss of

power and overheating. The following table shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the

gage number, the heavier the cord.

Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the

contaminated dust. The greatest danger of lead poisoning is to children and pregnant women.

Since it is difficult to identify whether or not a paint contains lead without a chemical analysis,

we recommend the following precautions when sanding any paint:

• No children or pregnant women should enter the work area where the paint sanding is

being done until all clean up is completed.

• A dust mask or respirator should be worn by all persons entering the work area. The filter

should be replaced daily or whenever the wearer has difficulty breathing.

   NoTe: Only those dust masks suitable for working with lead paint dust and fumes should

be used. Ordinary painting masks do not offer this protection. See your local hardware

dealer for the proper (NIOSH approved) mask.

• NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting

contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking

or smoking. Articles of food, drink, or smoking should not be left in the work area where dust

would settle on them.

• Paint should be removed in such a manner as to minimize the amount of dust generated.

• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils

thickness.

• Sanding should be done in a manner to reduce tracking of paint dust outside the work area.

• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the

duration of the sanding project. Vacuum filter bags should be changed frequently.

• Plastic drop cloths should be gathered up and disposed of along with any dust chips or

other removal debris. They should be placed in sealed refuse receptacles and disposed of

through regular trash pick-up procedures. During clean up, children and pregnant women

should be kept away from the immediate work area.

• All toys, washable furniture and utensils used by children should be washed thoroughly

before being used again.

120V

0-25

26-50

51-100  101-150

240V

0-50

51-100  101-200  201-300

More  Not more

Than Than

0  -  6

18

16

16

14

6  -  10

18

16

14

12

10  -  12

16

16

14

12

12  -  16

14

12

Not Recommended

ON OFF SWITCH

INTERRUPTEUR

INTERRUPTOR DE ENCENDIDO Y APAGADO

 

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below

are used to help you recognize this information.

Indicates  an  imminently  hazardous  situation  which,  if  not  avoided,  will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially haz ard ous situation which, if not avoided, may

result in minor or mod er ate injury.

Used without the safety alert symbol indicates potentially hazardous situation

which, if not avoided, may result in property damage.