Bertazzoni 24/30 Speed Oven 业主指南
3
USA
Installation instructions
Before installation
Check that the input voltage indicated on the
characteristics plate is the same as the voltage
of the power outlet you are going to use.
characteristics plate is the same as the voltage
of the power outlet you are going to use.
Open the oven door and take out all the
accessories and remove the packing material.
accessories and remove the packing material.
Do not remove the mica cover on the ceiling
of the interior! This cover stops fat and pieces
of food damaging the microwave generator.
of the interior! This cover stops fat and pieces
of food damaging the microwave generator.
Warning! The front surface of the oven may
be wrapped with a protective film. Before
using the oven for the first time, carefully
remove this film, starting on the inside.
be wrapped with a protective film. Before
using the oven for the first time, carefully
remove this film, starting on the inside.
Make sure that the oven is not damaged in
any way. Check that the oven door closes
correctly and that the interior of the door and
the front of the oven opening are not damaged.
If you find any damage contact the Technical
Assistance Service.
any way. Check that the oven door closes
correctly and that the interior of the door and
the front of the oven opening are not damaged.
If you find any damage contact the Technical
Assistance Service.
DO NOT USE THE OVEN if the power cable or
the plug is damaged, if the oven does not
function correctly or if it has been damaged or
dropped. Contact the Technical Assistance
Service.
the plug is damaged, if the oven does not
function correctly or if it has been damaged or
dropped. Contact the Technical Assistance
Service.
Put the oven on a flat and stable surface. The
oven must not be put close to any sources of
heat, radios or televisions.
oven must not be put close to any sources of
heat, radios or televisions.
During installation, make sure that the
power cable does not come into contact
with any moisture or objects with sharp
edges behind the oven. High temperatures
can damage the cable.
power cable does not come into contact
with any moisture or objects with sharp
edges behind the oven. High temperatures
can damage the cable.
Warning: after the oven is installed you
must make sure you can access the plug.
must make sure you can access the plug.
After installation
The oven is equipped with a power cable and a
plug for single phase current.
plug for single phase current.
If the oven is to be installed on a permanent
basis it should be installed by a qualified
basis it should be installed by a qualified
technician. In such a case, the oven should be
connected to a circuit with an all-pole circuit
breaker with a minimum separation of 3 mm
between contacts.
connected to a circuit with an all-pole circuit
breaker with a minimum separation of 3 mm
between contacts.
WARNING: THE OVEN MUST BE EARTHED.
The manufacturer and retailers do not
accept responsibility for any damage that
may be caused to people, animals or property
if these installation instructions are not
observed..
accept responsibility for any damage that
may be caused to people, animals or property
if these installation instructions are not
observed..
The oven only functions when the door is
closed correctly.
closed correctly.
After the first use, clean the inside of the oven
and the accessories, following the cleaning
instructions given in the section “Oven cleaning
and maintenance”.
and the accessories, following the cleaning
instructions given in the section “Oven cleaning
and maintenance”.
Fit the Turntable support in the centre of the
oven cavity and put the Turntable ring and the
Turntable plate on top, making sure they slot
in. Whenever you use the microwave, the
turntable plate and the respective accessories
must be inside and correctly fitted. The
turntable plate can rotate in both directions.
oven cavity and put the Turntable ring and the
Turntable plate on top, making sure they slot
in. Whenever you use the microwave, the
turntable plate and the respective accessories
must be inside and correctly fitted. The
turntable plate can rotate in both directions.
During installation, follow the instructions supplied separately.