Beltronics Vector 995 业主指南
Problem
V995 beeps briefly at the same
location every day, but no radar
source is in sight.
location every day, but no radar
source is in sight.
V995 does not seem sensitive to
radar or laser.
radar or laser.
V995 did not alert when a police
car was in view.
car was in view.
V995 did not provide a Safety signal
while within range of an
emergency vehicle.
while within range of an
emergency vehicle.
V995’s display is not working.
V995’s audible alerts are less loud
after the first few alerts.
after the first few alerts.
V995 bounces or sags on
windshield.
windshield.
V995’s power-on sequence
reoccurs while you are driving.
reoccurs while you are driving.
Solution
• An X or K-band motion sensor or intrusion alarm is located
within range of your route. With time, you will learn
predictable patterns of these signals.
within range of your route. With time, you will learn
predictable patterns of these signals.
• Make sure that windshield wipers do not block V995’s radar
antenna and that the laser lens is not behind tinted areas.
• Determine if your vehicle has an Instaclear®, ElectriClear®
or solar reflective windshield which may deflect radar or laser
signals.
• V995 may be in City Mode.
antenna and that the laser lens is not behind tinted areas.
• Determine if your vehicle has an Instaclear®, ElectriClear®
or solar reflective windshield which may deflect radar or laser
signals.
• V995 may be in City Mode.
• VASCAR (Visual Average Speed Computer and Recorder) a
stopwatch method of speed detection, may be in use.
• Officer may not have radar or laser unit turned on.
stopwatch method of speed detection, may be in use.
• Officer may not have radar or laser unit turned on.
• Safety transmitters may not be commonly used in your area.
• Press the BRT button to deactivate Dark Mode.
• V995 is in AutoMute Mode. See page 8 for details.
• V995 is not making contact with the windshield to provide
stability. While holding down V995’s QuickMount button,
slide V995 toward the windshield so that the back top edge
makes firm contact.
stability. While holding down V995’s QuickMount button,
slide V995 toward the windshield so that the back top edge
makes firm contact.
• A loose power connection or dirty lighter socket can cause
V995 to be briefly disconnected.
V995 to be briefly disconnected.
Problem
Your 14-year old son has changed
all 7 of the Programming options.
all 7 of the Programming options.
V995 will not turn on.
V995 feels very warm.
Solution
• You can return all of the programming options to the
factory defaults by holding down the CITY and BRT buttons
while you turn V995 on.
factory defaults by holding down the CITY and BRT buttons
while you turn V995 on.
• Check that the power is ON.
• Check that vehicle ignition is ON.
• Check that vehicle lighter socket is functional.
• Try
• Check that vehicle ignition is ON.
• Check that vehicle lighter socket is functional.
• Try
V995
in another vehicle.
• It is normal for V995 to feel warm.
Explanation of Displays
AD
Sensitivity control is in Auto mode, display is in Dark mode (page 9)
HD
Sensitivity control is in Highway mode, display is in Dark mode (page 9)
CD
Sensitivity control is in City mode, display is in Dark mode (page 9)
No display
V995 is in the Dark mode (page 9)
PilotHWY
One of the many programming messages (pages 12-16)
WorkZone
One of the many Safety Radar messages (pages 22-23)
Caution
V995 has detected a Safety Radar Signal, but the signal isn’t yet strong
enough to decode the specific safety message (page 22-23)
Self Cal
V995 is running a self-calibration test
Service
V995 has failed the calibration test. Contact Beltronics for repair
Required
24
25
Troubleshooting