Behringer Europack UB2222FX-Pro 业主指南

EURORACK UB2442FX-PRO/UB2222FX-PRO/UB1832FX-PRO/UB1622FX-PRO User Manual

STEREO AUX RETURN 1/2 (TO AUX SEND)
The two right-hand STEREO AUX RETURN controls have a special function:  

they can be used to add an effect to a monitor mix. An example follows 

(UB1622FX-PRO wired to an effects device):

Monitor mix with effect
In this instance, your effects device should be set up as follows: the AUX SEND 2 

jack should be connected to the L/Mono input of your effects device, with its 

outputs coming back into the STEREO AUX RETURN 1 jacks.
Connect the AUX SEND 1 jack output to the amplifier of your monitor system. 

The AUX SEND 1 master control determines the overall volume of the 

monitor mix.
Using the STEREO AUX RETURN (TO AUX SEND) control, the effect signal can now 

be blended into the monitor mix.
You can easily use the headphones distribution amplifier BEHRINGER POWERPLAY 

PRO HA4700/HA8000 to provide four (HA8000: eight) stereo headphone mixes for 

your studio.
The following table shows which jacks on the console can be used 

for this purpose.

AUX SEND 2

STEREO AUX RETURN 1 

Connectors

STEREO AUX RETURN 1  

(TO AUX SEND 1) Control

AUX SEND 1

STEREO AUX RETURN 2 

Connectors

MONITOR Switch of the 

FX/AUX 2 RET

AUX SEND 2

STEREO AUX RETURN 

Connectors 1 or 2

STEREO AUX RETURN 1  

(TO AUX SEND 1) Control

AUX SEND 2

STEREO AUX RETURN 1 

Connectors

STEREO AUX RETURN 1  

(TO AUX SEND 1) Control

AUX SEND 1

STEREO AUX RETURN 2 

Connectors

STEREO AUX RETURN 2  

(TO AUX SEND 2) Control

Tab. 2.1: Connectors and controls for monitor mix with effect

STEREO AUX RETURN FX
On consoles UB1622FX-PRO and UB1832FX-PRO this is the STEREO AUX 

RETURN 2, on consoles UB2222FX-PRO and UB2442FX-PRO this is the 

STEREO AUX RETURN 3.
Use the STEREO AUX RETURN FX control to determine the level of the signal 

routed from the AUX RETURN FX jacks to the main mix. If nothing is connected to 

these jacks, the output of the built-in effects module will appear.

MAIN MIX / TO SUBS 
This switch routes the signal fed in via the STEREO AUX RETURN FX jacks either to 

the main mix (not pressed) or to the submix (pressed).
On the UB2442FX-PRO you can select which subgroup the signal is assigned to 

(switches 1-2 / 3-4, to the right of MAIN MIX / TO SUBS).

SOLO RETURNS
Additionally, this model allows you to route the aux returns together to the solo 

bus and the PFL bus. The LED lights up when Solo is on. 

STEREO AUX RETURN 4 (UB2442FX-PRO only)
This control behaves the same way as the other stereo aux returns. 

Additionally, it provides for a simple monitor path using the switch PHONES/CTRL 

ROOM ONLY.

PHONES/CTRL ROOM ONLY
Use this switch to route the signal appearing at the AUX RETURN 4 jacks to the 

control room and headphones outputs.

2.3.6  Supplement to UB1832FX-PRO
The UB1832FX-PRO has a stereo fader for the AUX RETURN FX and offers a variety 

of routing options: MUTE disables the effect return (but not PFL of course!), 

SOLO routes it to the Solo or PFL busses, SUB to the subgroups and MAIN to the 

main mix.

UB1832FX-PRO

Fig. 2.13: The FX/AUX 2 return fader of the UB1832FX-PRO

MON
The MON switch routes the signals appearing at the AUX RETURN 2 jacks to the 

monitor path, along with the monitor signals from the channels.
If you wish to route the effect signal to the monitor mix, you can also switch aux 

1 to pre-fader, drive the effect device from the aux 1 output and return the effect 

signal via AUX RETURN 2 to the monitor signal.