Broil-Mate 115997 NG 用户手册

After you have finished, prepare for the next cookout by 

burning off any residue of food from the grid and briquettes, 

Flav-R-Wave™ or Flav-R-Cast™ in the following manner: 
Cooking Grids 
Remove all food from the grids, turn the control knobs to 

“HIGH”, and operate the barbecue with the lid closed for 5 

to 10 minutes or until smoking stops.  Turn the gas cylinder 

valve to OFF, then the control knobs to OFF. 
Use a long-handled brass wire brush to clean the grids.  

Remember that the barbecue is hot, so wear kitchen mitts 

or use a pot-holder to handle the brush. 
You do not have to wash the grids and upper cooking rack 

after each cookout, but if you wish to do so, use a mild 

soap and water solution, then rinse them thoroughly.  Never 

use a commercial oven cleaner. 
Porcelain Coating - Most OMC cooking grids are coated 

with a durable porcelain enamel to assist in cleaning and 

reduce the tendency of food sticking to the grid. Some 

chipping may occur if mishandled.  This will not affect the 

use or performance of the grids.  If some rust appears, 

remove the rust with a scrub pad and coat the grid with 

cooking oil.  

 

10 

Ceramic Briquets 
If any residue begins to 

accumulate on the briquets, 

remove the cooking grids and 

turn the briquets over prior to 

lighting the barbecue. Be sure 

to place briquets evenly in one 

layer. The underside of the 

briquets will self clean while 

preheating the barbecue. 
Flav-R-Wave™ 

If any residue begins to  

accumulate on the  

Flav-R-Wave™, remove cooking  

grids and scrape excess residue  

with back of barbecue brush. 
Flav-R-Cast™ 
Excess food residue may be 

removed using a scrub pad or 

brass grill brush.  Coat the 

Flav-R-Cast™ with cooking 

oil when not using the barbecue for an extended period.  

The Flav-R-Cast™ is coated with a matte porcelain finish to 

assist in cleaning and help prevent rust.  Some chipping 

may occur if mishandled.  This will not affect the use or 

performance of the Flav-R-Cast™.  If rust appears, remove 

the rust with a scrub pad and coat with cooking oil. 
Grease Cup Holder 

The grease cup holder is located on the bottom of 

the cooking oven immediately below the hole 

through which grease will drain.  The grease cup 

is not provided.  The clip, however, has been 

designed to hold a standard soup can or jar.  

Simply snap the can or jar into place.  The grease 

cup should be checked and replaced regularly to 

prevent grease from overflowing onto your patio. 

 

General Cleaning 
When the barbecue is cold, remove the grids.  If equipped 

with briquets, turn over.  Cover three quarters of the 

briquettes, Flav-R-Wave™ or Flav-R-Cast™ with aluminum 

foil, shiny side down.  Ignite the burners; operate the 

barbecue on HIGH with the lid closed for 10 minutes or until 

smoking stops.  Turn the gas cylinder valve to OFF, turn the 

control knobs to OFF.  When the barbecue is cool, remove 

the foil, and residue from briquettes, Flav-R-Wave™, Flav-

R-Cast™ with a vacuum. Remove briquets and grate or 

Flav-R-Wave™, Flav-R-Cast™, then clean the interior of 

the bottom oven by scrapping the sides and vacuuming. 

To ensure safe and efficient performance, the following 

components should be inspected and cleaned at least once 

per year or after any period of storage exceeding one month. 

Burner 
Remove burner and inspect for cracks and deterioration.   

Clean venturi tubes using a 
pipe cleaner or venturi 
brush to eliminate any 
blockages caused by 
spiders or insects.  See 
"Venturi Tubes". 

 

While burner is removed, clean interior of bottom oven by 

scrapping the sides and vacuuming. 

Hose 
Inspect and replace if necessary.  See "Hose and Regulator". 

Perma-Mold Shelves 
Wash with soap and water. To enhance luster, coat lightly 

with cooking oil. 
Exterior Finish 
If white oxidation spots appear, wash the outside of the 

housing with a mild soap and water solution.  Rinse the 

surfaces thoroughly, then wipe them with a cloth dipped in 

cooking oil to restore the luster. 
For repair of paint scratches and scuffs, use a good quality 

HIGH temperature (600°F) spray paint for touch-up. 

Replacement Parts 
If a problem is found with the regulator, hose, burner, or 

control valves, do not attempt repair.  See your dealer, 

approved service centre, or contact the factory for repairs 

or replacement parts.  To ensure optimum performance, 

use only original OMC replacement parts. 

Leak Test 
After reconnecting gas cylinder, be sure to check for leaks. 

See "Leak Testing"