Bosch Appliances Video Game Controller D9412GV2 用户手册

下载
页码 158
D9412GV2/D7412GV2 | Program Entry Guide | 6.0  GV2AUX 
EN | 140 
 
 
Bosch Security Systems, Inc. | 10/08 | F01U003636-04 
Fire Supv Res Type 
Early Ambush Timer 
Default: 
Default: 
10 min 
Selection: 
0, 1, 2 
Selection: 
5 to 30 min 
The control panel sends a FIRE 
TROUBLE RESTORE when a Fire 
Supervision point restores to normal. 
The programmed time is the maximum value of the 
Early Ambush Timer. When Early Ambush is set to 
Yes for a specified area (refer to A# Early Ambush on 
page 
The control panel sends a FIRE 
ALARM RESTORE when a Fire 
Supervision point restores to normal. 
48) and the area is disarmed, the user has the 
amount of time programmed here to enter a second 
code into the keypad. 
 
The control panel sends a FIRE 
SUPERVISION RESTORE when a 
Fire Supervision point restores to 
normal. 
If a second pass code is not entered within the 
programmed time, a Duress event is generated based 
on the first user code. Duress reports must be 
enabled in Routing in order to be sent to a central 
station.  
Determines how the control panel sends a Fire 
Supervision Restoral Event. 
 
Secondary Ambush Code 
 
The Fire Supv Restore Event is part of 
 
Fire Events in Routing. If Fire Supervision 
Default: 
Unique 
Restore Events are needed, simply 
Selection: 
Unique or any 
enable them in Routing. 
The code used to end the timer must 
be different from the code used to 
disarm the area. 
Unique 
 
Enable Protocol Type 
Default: 
No 
The timer can be stopped using a 
different code, or the same code that 
disarmed the area. 
Any 
Selection: 
Yes or No 
Not required. Leave at default value. 
The Secondary Ambush Code determines whether 
the same pass code can be used to begin and end 
the Early Ambush process. 
 
Fire Trouble Resound 
Default: 
Abort Window 
Selection: 
0, 1, 2 
Default: 
30 sec 
Keypads do not re-sound the fire 
trouble tone. 
Selection:  15 to 45 sec 
Keypads re-sound the fire trouble 
tone at 12:00 PM if any Fire point 
that falls within the scope of a 
keypad is in an off-normal condition. 
 
This parameter determines the amount of time the 
control panel delays a Burglar Alarm event from a 
point with P## Alarm Abort set to Yes. If an alarm 
silence operation is performed before this time 
elapses, the alarm transmission is aborted and the 
keypad shows an optional ALARM NOT SENT 
message. When an alarm transmission is successfully 
aborted, no event is written to the control panel event 
log. 
Keypads re-sound the fire trouble 
tone at 12:00 AM if any Fire point 
that falls within the scope of a 
keypad is in an off-normal condition. 
This item determines if a fire trouble condition, 
previously acknowledged and silenced at a keypad, 
automatically (locally) re-sounds the fire trouble tone 
at 12:00 PM, 12:00 AM, or not at all if the point is still 
in an off-normal state. Events are not generated at the 
time the re-sound occurs. 
When an abort alarm timer starts, it does not stop 
until an alarm silence operation is performed or the 
time expires. 
 
This feature does not apply to Fire Alarms 
or invisible point alarms. 
 
For SIA CP-01 Compliance: 
Abort Window
 is a required parameter.