Whirlpool WDF510PAYB 业主指南

NOTE: For most water conditions, the 
factory setting will give good results. If 
you have hard water or notice rings or 
spots, try a higher setting. Turn the 
arrow adjuster inside the dispenser by 
either using your fingers or inserting a 
flat-blade screwdriver into the center of 
the arrow and turning. 

Press the Select Cycles button until the light below the desired 
cycle is on.

NOTE: Heavier cycles and options affect cycle length. Some 
cycles and options will take up to 3

¹⁄₂ hours to complete.

Heavy

 – Use for heavily 

soiled, hard-to-clean 
items.

Normal

 – This cycle is 

recommended to 
completely wash a full 
load of normally soiled 
dishes. Selecting this 
cycle will default to the 
options recommended 
for normal amounts of food soil. The energy label is based on this 
cycle.

ECO

 – Use for lightly soiled items. It saves energy.

1-HR Wash

 – Use for lightly soiled items. For fast results, 1-Hr 

Wash will clean the dishes using slightly more water and energy.

Overnight cycle

 

– Use for loads with heavy amounts of food soil. 

It is a longer cycle and therefore is ideal to run overnight.

Rinse Only

 – (no options apply to this cycle) Do not use detergent. 

This is only a rinse that keeps food from drying on your dishes and 
reduces odor buildup in your dishwasher until you are ready to 
wash a full load.

You can customize your cycles by pressing the options desired. 

Repeatedly press the button until 
the desired combination of options 
is selected. 

High Temp

 – (can be selected with 

Heavy and Normal wash cycles) 
heats the water during the wash 
portions of the cycle. 

Sani Rinse

 – (can be selected with Heavy and Normal wash 

cycles) Select this option to raise the water temperature in the final 
rinse to approximately 155°F (68°C). Sani Rinse option adds heat 
and time to the cycle. This high temperature rinse sanitizes your 
dishes and glassware in accordance with NSF/ANSI Standard 184 
for Residential Dishwashers. Certified residential dishwashers are 
not intended for licensed food establishments.

Heat Dry

 – (can be selected with 1-HR Wash, Heavy and Normal 

wash cycles) When selected with the 1-Hr Wash cycle, the time is 
increased by approximately 30 minutes.

4-HR Delay

 – (any cycle) offers the choice to start the dishwasher 

automatically at a later time. Select a wash cycle and options. 
Press 4-HR Delay. Press START/RESUME. Close the door firmly.

Lock

 – (on 4-HR Delay button) use to avoid unintended use of your 

dishwasher. When Control Lock is lit, all buttons are disabled. The 
dishwasher door can be opened while the controls are locked.

To turn on Lock:
Press and hold 4-HR Delay for at least 3 seconds. The Locked light 
glows. If you press any pad while your dishwasher is locked, the 
light flashes 3 times.

To turn off Lock:
Press and hold 4-HR Delay for at least 3 seconds. The Control 
Lock light turns off.

■

Run hot water at the sink nearest your dishwasher until the 
water is hot. Turn off water.

■

Push door firmly closed. The door latches 
automatically. Select the wash cycle and options 
desired OR press START/RESUME to repeat the 
same cycle and options as in the previous wash 
cycle. For top controls, select cycle and options 
first, and then close the door. 

■

You can add an item anytime before the main 
wash starts. Open the door slowly and add the 
item. Close the door firmly. Press START/
RESUME.

■

The Clean indicator glows when the cycle is 
finished. Sanitized glows when Sani Rinse 
option is selected and sanitization levels 
occur.

max

fill

- -

-

-

- - - -

-

-

-

-