White Outdoor Two Stage Snow Blower 用户手册

1.  Do not put hands or feet near rotating parts, in the auger/

impeller housing or chute assembly. Contact with the 
rotating parts can amputate hands and feet. 

2.  The auger/impeller control lever is a safety device. Never 

bypass its operation. Doing so makes the machine unsafe 
and may cause personal injury. 

3.  The control levers must operate easily in both directions 

and automatically return to the disengaged position when 
released. 

4.  Never operate with a missing or damaged chute assembly. 

Keep all safety devices in place and working.

5.  Never run an engine indoors or in a poorly ventilated area. 

Engine exhaust contains carbon monoxide, an odorless and 
deadly gas. 

6.  Do not operate machine while under the influence of alcohol 

or drugs. 

7.  Muffler and engine become hot and can cause a burn. Do 

not touch.

8.  Exercise extreme caution when operating on or crossing 

gravel surfaces. Stay alert for hidden hazards or traffic.

9.  Exercise caution when changing direction and while operat-

ing on slopes. 

10. Plan your snow-throwing pattern to avoid discharge towards 

windows, walls, cars etc. Thus, avoiding possible property 
damage or personal injury caused by a ricochet. 

11. Never direct discharge at children, bystanders and pets or 

allow anyone in front of the machine. 

12. Do not overload machine capacity by attempting to clear 

snow at too fast of a rate.

13. Never operate this machine without good visibility or light. 

Always be sure of your footing and keep a firm hold on the 
handles. Walk, never run.

14. Disengage power to the auger/impeller when transporting or 

not in use.

15. Never operate machine at high transport speeds on slippery 

surfaces. Look down and behind and use care when 
backing up. 

16. If the machine should start to vibrate abnormally, stop the 

engine, disconnect the spark plug wire and ground it against 
the engine. Inspect thoroughly for damage. Repair any 
damage before starting and operating.

17. Disengage all control levers and stop engine before you 

leave the operating position (behind the handles). Wait 
until the auger/impeller comes to a complete stop before 
unclogging the chute assembly, making any adjustments, or 
inspections. 

18. Never put your hand in the discharge or collector openings. 

Always use the clean-out tool provided to unclog the dis-
charge opening. Do not unclog chute assembly while engine 
is running. Shut off engine and remain behind handles until 
all moving parts have stopped before unclogging.

19. Use only attachments and accessories approved by the 

manufacturer (e.g. wheel weights, tire chains, cabs etc.).

20. When starting engine, pull cord slowly until resistance is felt, 

then pull rapidly. Rapid retraction of starter cord (kickback) 
will pull hand and arm toward engine faster than you can let 
go. Broken bones, fractures, bruises or sprains could result.

21. If situations occur which are not covered in this manual, use 

care and good judgment. Call customer assistance for the 
name of your nearest servicing dealer.

1.  Never tamper with safety devices. Check their proper 

operation regularly. Refer to the maintenance and adjust-
ment sections of this manual.

2.  Before cleaning, repairing, or inspecting machine disengage 

all control levers and stop the engine. Wait until the auger/
impeller come to a complete stop. Disconnect the spark plug 
wire and ground against the engine to prevent unintended 
starting.

3.  Check bolts and screws for proper tightness at frequent 

intervals to keep the machine in safe working condition. 
Also, visually inspect machine for any damage. 

4.  Do not change the engine governor setting or over-speed 

the engine. The governor controls the maximum safe 
operating speed of the engine.

5.  Snow thrower shave plates and skid shoes are subject to 

wear and damage. For your safety protection, frequently 
check all components and replace with original equipment 
manufacturer’s (OEM) parts only. “Use of parts which do 
not meet the original equipment specifications may lead to 
improper performance and compromise safety!”

6.  Check controls periodically to verify they engage and 

disengage properly and adjust, if necessary. Refer to the 
adjustment section in this operator’s manual for instructions.

7.  Maintain or replace safety and instruction labels, as neces-

sary.

8.  Observe proper disposal laws and regulations for gas, oil, 

etc. to protect the environment.

9.  Prior to storing, run machine a few minutes to clear snow 

from machine and prevent freeze up of auger/impeller.

10. Never store the machine or fuel container inside where 

there is an open flame, spark or pilot light such as a water 
heater, furnace, clothes dryer etc.

11. Always refer to the operator’s manual for proper instructions 

on off-season storage.

12. Check fuel line, tank, cap, and fittings frequently for cracks 

or leaks. Replace if necessary.

13. Do not crank engine with spark plug removed.

To avoid serious injury or death, do not modify engine in any 
way. Tampering with the governor setting can lead to a runaway 
engine and cause it to operate at unsafe speeds. Never tamper 
with factory setting of engine governor.

Engines which are certified to comply with California and federal 
EPA emission regulations for SORE (Small Off Road Equipment) 
are certified to operate on regular unleaded gasoline, and may 
include the following emission control systems: Engine Modifica-
tion (EM) Oxidizing Catalyst (OC), Secondary Air Injection (SAI) 
and Three Way Catalyst (TWC) if so equipped.

According to the Consumer Products Safety Commission 
(CPSC) and the U.S. Environmental Protection Agency (EPA), 
this product has an 

Average Useful Life of seven (7) years, or 

60 hours of operation. At the end of the 

Average Useful Life, 

have the machine inspected annually by an authorized service 
dealer to ensure that all mechanical and safety systems are 
working properly and not worn excessively. Failure to do so can 
result in accidents, injuries or death.

This symbol points 
out important safety 
instructions, which 
if not followed, could 
endanger the per-
sonal safety and/or 
property of yourself 
and others. Read and 
follow all instructions 
in this manual before 
attempting to operate 
this machine. Failure 
to comply with these 
instructions may 
result in personal 
injury. When you see 
this symbol, HEED 
IT’S WARNING!
Your Responsibility 
Restrict the use 
of this power machine 
to persons who read, 
understand 
and follow the warnings 
and instructions 
in this manual 
and on the machine. 

05.08.08