Weed Eater WE261 用户手册

12

The op er a tion of any riding mower can  result in foreign objects thrown 

into the eyes, which can result in severe eye dam age.  Al ways wear 

safety glass es or eye shields while op er at ing your riding mower or 

per form ing any ad just ments or repairs.  We rec om mend a wide vi sion 

safe ty mask over spec ta cles or stan dard safety glass es.

TO SET PARKING BRAKE 
Your riding mower is equipped with an opera-

tor presence sens ing  switch.  When engine 

is running, any attempt by the op er a tor to 

leave the seat without first setting the parking 

brake will shut off the engine.

1.  Depress brake pedal all the way down 

and hold.

2.  Depress parking brake lever and re lease 

pres sure from brake pedal.  Pedal should 

re main in brake position.  Make sure 

parking brake will hold riding mower 

secure.

TO MOVE FORWARD AND BACK WARD 
The direction and speed of movement  is 

controlled by the motion control lever. 

1.  Start riding mower with clutch/brake pedal 

depressed and motion control lever in 

neutral (N) position.

2.  Move motion control lever to desired  

po si tion. 

3.  Slowly release clutch/brake pedal to start  

movement.

IMPORTANT:  Bring riding mower to a com-

plete stop before shifting or changing gears. 

Failure to do so will shorten the useful life of 

your transaxle. 
TO ADJUST MOWER CUT TING HEIGHT
The po si tion of the mower height deck lift 

le ver de ter mines the cut ting height.

•  Grasp lift le ver.

•  Press lift lever plunger with thumb and 

move lever to desired position.

The cutting  height  range is  ap prox i mate ly 

1-1/2 to  4".  The heights are measured from 

the ground to the blade tip with the engine 

not running.  These heights are approximate 

and may vary depending upon soil condi-

tions, height of grass and types of grass 

being mowed.

•  The average lawn should be cut to ap-

proximately 2-1/2" during the cool season 

and to over 3" during hot months.  For 

healthier and better looking lawns, mow 

often and after moderate growth.

•  For best cutting performance, grass over 

6" in height should be mowed twice.  Make 

the first cut relatively high; the second to 

de sired height.

STOPPING 
MOWER BLADE -
•  To stop mower blade, move deck clutch 

lever to disengaged po si tion.

GROUND DRIVE -
•  To stop ground drive, depress  brake pedal 

all the way down.

ENGINE - 

•  Turn ignition key to “STOP” position and re-

move key.  Always remove key when leaving 

riding mower to prevent un au tho rized use.

IMPORTANT:  Leaving the ignition switch in 

any position other than "STOP" will cause 

the battery to discharge and go dead.

NOTE:  Under certain conditions when riding 

mower is standing idle with the engine run-

ning, hot engine exhaust gases may cause 

“browning” of grass.  To eliminate this pos-

sibility, always stop engine when stopping 

riding mower on grass areas.

 CAUTION:  Always stop riding mower 

com plete ly, as described above, before 

leav ing the operator's position.

Motion 

Control 

Lever

Mower Height 

Adjustment

Brake Pedal 

"Engaged" 

Position

Deck Clutch 

Lever 

"Engaged" 

Position

Deck Clutch 

Lever 

"Disengaged" 

Position

Brake Pedal 

"Drive" 

Position

Parking Brake 

Pedal-Push Down 

to "Engage"

29

1 

532 43 70-70 

BATTERY

2 

532 42 54-16 

FOAM, POLYURETHANE

3 

532 19 33-50 

SWITCH, IGN, DLTA, P-IN, ROS

4 

532 41 19-33 

KEY, MOLDED ENGLISH/SPANISH

- - 

532 41 19-35 

KEY, MOLDED ENGLISH/FRENCH/INTERNATIONAL

5 

532 43 33-30 

FUSE, 5A

6 

532 42 59-37 

FUSE, 40A

7 

532 16 07-84 

SWITCH, PLUNGER, NO, OLIVE

8 

532 43 15-42 

RELAY, 40A

9 

532 10 95-53 

SWITCH, INTLK,CL, MWR, GRY

10 

532 17 61-38 

SWITCH, INTERLOCK, NONC,GRAY

11 

532 43 18-46 

MODULE, STARTING, RECOIL, LRV

12 

532 19 27-49 

SWITCH, SEAT, DP, ROS

13 

532 42 84-77 

HARNESS, IGN, ELECTSTART, LRV

14 

532 10 97-48 

RELAY

NOTE: All component dimensions given in U.S. inches

         1 inch = 25.4 mm