Weed Eater WE261 用户手册

8

NOTE:  You may now roll your riding 

mower off the skid. Follow the ap pro pri ate 

instruction below to remove the riding mower 

from the skid.

The tires on your riding mower were 

overinflated at the factory for shipping pur-

poses.  Correct tire pressure is important 

for best cutting performance.

•  Reduce tire pressure to PSI shown on 

tires.

For best cutting results, mower housing 

should be properly leveled.  See “TO LEVEL 

MOWER HOUSING” in the Service and 

Adjustments section of this manual.

See the figure that is shown for replacing 

the mower drive belt in the service and 

adjustment section of this manual.  Verify 

that the belt is routed correctly.

After you learn how to operate your rid-

ing mower, check to see that the brake 

is operating properly.  See “TO ADJUST 

BRAKE” in the Service and Adjustments 

section of this manual.

02464

Adjustment Knob

Flat Washer

4.  Pivot seat and pan forward and as sem ble 

adjustment knob and flat washer loosely. 

Do not tighten.

5.  Lower seat into operating position and 

sit in seat.

6.  Slide seat until a comfortable position is 

reached which allows you to press clutch/

brake pedal all the way down.

7.  Get off seat without moving its ad just ed 

position.

8.  Raise seat and tighten adjustment knob 

securely.

CHECK BATTERY
Make sure battery is securely fastened, 

and that all wires are securely connected.

•  Battery is located under the seat.

•  Battery has been fully charged from the 

factory, before installation.

Battery

Seat

  WARNING: Before starting, read, un-

 der stand and follow all in struc tions in the 

Operation section of this manual. Be sure 

riding mower is in a well-ventilated area. 

Be sure the area in  front of riding mower is 

clear of other people and objects.

1. Raise deck lift lever to its highest 

position.

2.  Release parking brake by depressing 

clutch/brake ped al.

3. Engage freewheel control. See “TO 

TRANSPORT” in the operation section 

of this manual.

4.  Roll riding mower forward off skid.

33

NOTE: All component dimensions given in U.S. inches

         1 inch = 25.4 mm

–  –    532 43 61-44    SERVICE KIT, TRANSAXLE

1  

532 43 64-98 

WHEEL ASM (REAR)

2  

532 12 17-48 

WASHER, 16 GA.

3  

812 00 00-01 

E-CLIP

4  

532 12 35-83 

KEY. SQUARE

5  

532 42 79-39 

WELDMENT. DRIVE AXLE

6  

532 42 80-69 

CHAIN DRIVE

7  

532 42 78-73 

SPROCKET. 9 TOOTH  

  

SPLINED

8  

812 10 00-09 

RING, SNAP

10  

532 42 88-76 

DIFFERENTIAL ASM

11  

532 00 13-70 

WASHER, THRUST

12  

532 43 06-45 

CHAIN, PRIMARY DRIVE

13  

532 43 08-45 

BUSHING

14  

532 43 85-68 

BRACKET, CARRIER

15  

532 12 47-93 

BEARING ASM

16  

532 42 79-26 

SHAFT INPUT

17  

532 43 72-81 

WHEEL, FRICTION A5M

18  

532 42 47-59 

ARM, SHIFT

19  

532 43 08-70 

ROD, BYPASS

20  

532 42 79-97 

BRACE CARRIER REAR

21  

532 42 80-77 

SPRING, CARRIER

22  

532 42 80-76 

SPRING, BRAKE

23  

532 43 13-74 

SPRING, BYPASS

24  

532 42 79-95 

BRACE CARRIER BOX

25  

532 42 83-03 

LINK, SHIFT

26  

532 42 98-16 

ARM. CLUTCH

27  

532 42 90-53 

WELDMENT SHIFT LEVER

28  

532 42 83-02 

SUPPORT, SHIFT LEVER

29  

532 17 48-40 

WASHER, NYLON

30  

532 18 39-00 

HUB SHIFT LEVER

31  

532 42 90-55 

SPACER, NYLON

32  

532 42 84-64 

MNTG BRKT. SHIFT ARM

33  

532 42 84-61 

BRACKET, SHIFTER FLEX

34  

532 42 84-62 

TUBE SHIFT ARM

35  

532 41 15-55 

GRIP, HANDLE

36  

872 11 04-06 

BOLT, CARRIAGE - 114-20 X 3/4

37  

873 80 04-00 

NUT NYLON LOCK 114-20

38  

532 16 54-92 

BOLT, SHOULDER

39  

874 78 04-12 

BOLT, 1/4-20 X 3/4

40  

810 04 04-00 

WASHER, LOCK

41  

819 09 12-10 

WASHER FLAT

42  

532 16 60-02 

WASHER, SERRATED

43  

873 68 04-00 

NUT, CROWN LOCK 114-20

45  

817 49 04-36 

SCREW 1/4-20 X 2 114

46  

819 09 10-16 

WASHER

47  

817 49 04-20 

SCREW, 1/4-20 X 1 1/2

48  

532 43 02-49 

PLATE BRAKE ANTI - ROTATE

49  

532 43 02-45 

SPRING, BRAKE RETURN

50  

532 42 80-21 

ARM, BRAKE

51  

532 43 02-47 

SPACER RETURN

52  

532 42 80-78 

CALIPER, BRAKE ASM

53  

877 01 08-10 

PIN, DOWEL 1/4

54  

532 42 80-19 

PLATE, BRAKE PAD

55  

532 42 80-17 

PUCK BRAKE

56  

532 43 52-53 

ROTOR, BRAKE

57  

532 42 80-16 

CAP, BRAKE CALIPER

58  

532 12 47-88 

PIN, RETAINER

59  

817 49 05-08 

BOLT, 5/16-16 X 112

60  

532 44 08-55 

CABLE, BRAKE

61  

532 42 79-45 

WELDMENT, PEDAL

62  

532 42 96-78 

ROD, PARKING BRAKE

63  

877 10 08-12 

PIN, .25 X .75 CLEVIS

64  

532 42 10-76 

PIN, COTTER 5/64 X 3/4

65  

532 42 93-25 

BRACKET, BRAKE SUPPORT

66  

532 42 96-94 

COVER PEDAL

67  

532 42 96-93 

COVER, BRAKE PEDAL

68  

817 06 05-16 

SCREW, 1/4-20 X 3/8

69  

532 42 80-70 

BRAKE CABLE MOUNT

70  

817 00 05-12 

BOLT, 5/16-18 X 3/4

71  

532 43 64-99   CAP HUB AXLE

73  

532 42 95-19 

SPROCKET II TOOTH  

  

SPLINED

74  

532 43 78-41 

TENSION LRV CHAIN

75  

532 43 34-95 

SPROCKET IDLER

117   812 00 00-40 

RING KLIP #T5304-62