Rocketfish RF-HTS105 产品宣传页

 ENGLISH 10-1214

1  Plug the power cord of the Rocketfish Power Manager into a 

standard 120V AC outlet.  If the LEDs do not light up, press the 
main power switch/circuit breaker on the front of the unit.

2  Plug the power cord of your primary home theater device, such 

as a TV, into the Master outlet of the Power Manager. When this 
device is powered off or goes into a SLEEP or STANDBY mode, 
power to the devices plugged into the Master-controlled outlets 
will automatically be shut off, saving energy by preventing them 
from drawing any standby current.

3  Plug the power cords of your secondary devices, such as a 

Blu-ray/DVD player, A/V receiver, CD player, etc., into the 
Master-controlled outlets of the Power Manager.  
NOTE: Do not plug any device into a Master-controlled outlet 
that you wish to use while the power of the primary device 
plugged into the Master outlet is powered off, as these outlets 
only provide power to the connected devices while the primary 
device is powered on.

4  Plug the power cords of any devices that require constant power, 

such as a DVR/PVR, or devices that you wish to use while the 
primary device is powered off, into the Always-on outlets of the 
Power Manager. 

5  Connect the incoming coaxial cable source (i.e., the cable jack on 

the wall or incoming satellite line) to the coaxial jack marked IN 
on the Power Manager.

6  Connect a separate coaxial cable from the coaxial jack marked 

OUT on the Power Manager to the coaxial input jack of the 
cable/satellite set-top box.

7  After all devices have been properly plugged into the Power 

Manager and powered on, when you power the primary device 
that is plugged into the Master outlet on and off, the secondary 
devices that are plugged into the Master-controlled outlets will 
automatically power on and off.  Devices that are plugged into 
the Always-on outlets will not be controlled by the primary 
device, and must be powered on and off separately as desired.

NOTE: Should the Master-controlled outlets not power on and off 
as described when the primary device plugged into the Master 
outlet is powered on and off, it is possible that the primary 
device draws too much current while in the OFF or STANDBY 
mode.  In the event this should occur with your equipment, try 
plugging a different primary device into the Master outlet.

•  Load rating: 15 amps

•  Line voltage: 125V AC @ 60 Hz

•  Surge protection: 3 lines (L-N / L-G / N-G)

•  Maximum surge current: 105,000 amps

•  Maximum energy dissipation: 2,100 joules

•  Clamping voltage: L-N / L-G / N-G = 400 volts

•  EMI/RFI noise filtering: Up to 47 dB

•  Standby power consumption: 0.98 watts

• UL-1449 certified

•  RISK OF ELECTRIC SHOCK–Use only in dry locations and only 

indoors.

•  DO NOT plug into another relocatable power tap. 

•  DO NOT “daisy chain” surge protectors.

•  DO NOT use with any aquarium equipment. 

•  DO NOT use if correctly grounded outlets are not available. 

•  DO NOT install this device if there is not at least 30 feet 

(10 meters) or more of wire between the electrical outlet and 
electrical service panel.

See included warranty sheet, visit www.rocketfishproducts.com or 
call 800-620-2790 for additional connected equipment and 
product warranty information or for customer service.

© 2011 BBY Solutions, Inc., All Rights Reserved.
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and 
brand names are trademarks of their respective owners.