Amana PTH094G35AXXX 规格说明表单
P
roduct
S
PecificationS
6
www.amana-ptac.com
SS-DPTAC
Furnish and install air-cooled through-the-wall package terminal air conditioners amd heat pumps (assembled in the USA).
Units are rated in accordance with the ARI (Air Conditioning & Refrigeration Institute) Standards 310/380-93, CSA (Canadian
Standards Association) EEV certification programs and listed by U. L. (Underwriters Laboratories).
Units are rated in accordance with the ARI (Air Conditioning & Refrigeration Institute) Standards 310/380-93, CSA (Canadian
Standards Association) EEV certification programs and listed by U. L. (Underwriters Laboratories).
r
ATings
Each unit must meet the following specifications:
ARI rating of _________BTUH cooling (and _________ BTUH
reverse cycle heating with a COP of _________ at 47° F O.D.)
Electric resistance heat of _________ BTUH. Total Amp draw
must be of ________ and _________ Watts at _________ volts.
The unit must remove a minimum of _________ pints of
moisture per hour when operated at rating conditions. The EER
must be a minimum of _________ EER.
ARI rating of _________BTUH cooling (and _________ BTUH
reverse cycle heating with a COP of _________ at 47° F O.D.)
Electric resistance heat of _________ BTUH. Total Amp draw
must be of ________ and _________ Watts at _________ volts.
The unit must remove a minimum of _________ pints of
moisture per hour when operated at rating conditions. The EER
must be a minimum of _________ EER.
u
niT
C
HAssis
Each unit must be slide out design shipped with room cabinet
front installed. Unit chassis must have the ability to be installed
with 0 clearance from finished floor. An electrical power cord
must be included with chassis and installed by the manufacturer
to assure proper NEMA 6 or 7 configuration and UL-approved
length. Units less than 250 volts must also have a LCDI power cord.
Unit must be tested for conformance to ASTME water infiltration
specification ASTME 331-86, which ensures no water infiltration
when tested at 8" rain per hour at 63 mph wind for 15 minutes.
front installed. Unit chassis must have the ability to be installed
with 0 clearance from finished floor. An electrical power cord
must be included with chassis and installed by the manufacturer
to assure proper NEMA 6 or 7 configuration and UL-approved
length. Units less than 250 volts must also have a LCDI power cord.
Unit must be tested for conformance to ASTME water infiltration
specification ASTME 331-86, which ensures no water infiltration
when tested at 8" rain per hour at 63 mph wind for 15 minutes.
r
oom
C
AbineT
The monochromatic front of the room cabinet must be able to
be field-secured to chassis to inhibit tampering. Filter must be
accessible without removing room front. Cabinet depth must
not exceed 7⅝” to minimize unit’s impact on room space.
be field-secured to chassis to inhibit tampering. Filter must be
accessible without removing room front. Cabinet depth must
not exceed 7⅝” to minimize unit’s impact on room space.
C
onTrACTor
'
s
b
id
s
HeeT
C
oils
Unit’s coils must have rifled copper tubing expanded into
rippled-edge louvered aluminum fins. Exterior coil must be of
a two-row bent coil design with removable shroud top to allow
easy-access for cleaning of the exterior coil.
rippled-edge louvered aluminum fins. Exterior coil must be of
a two-row bent coil design with removable shroud top to allow
easy-access for cleaning of the exterior coil.
H
eAT
P
umPs
Each unit must include a change-over thermistor that senses an
outside ambient switch-over temperature as low as 24°F, lock-
open refrigerant reversing valve during heat pump operation,
temperature-activated defrost drain and automatic emergency
heat operation to override the heat pump’s change-over
thermostat and bring on electric resistance heaters in the event
of a sealed system failure. Unit must not operate compressor
and electric heaters simultaneously.
outside ambient switch-over temperature as low as 24°F, lock-
open refrigerant reversing valve during heat pump operation,
temperature-activated defrost drain and automatic emergency
heat operation to override the heat pump’s change-over
thermostat and bring on electric resistance heaters in the event
of a sealed system failure. Unit must not operate compressor
and electric heaters simultaneously.
C
omPressor
The compressor must be hermetically sealed, internally isolated,
rotary-type and permanently mounted on rubber isolators. No
removal or adjustment of compressor hold-down bolts is to be
required during installation.
rotary-type and permanently mounted on rubber isolators. No
removal or adjustment of compressor hold-down bolts is to be
required during installation.
W
ArrAnTy
The warranty is for Full One Year on the entire unit; Full 2nd through
5th Year on the entire sealed refrigerant system components;
Limited Second through Fifth Year on functional parts only.
5th Year on the entire sealed refrigerant system components;
Limited Second through Fifth Year on functional parts only.
P
roduCT
s
PeCifiCATions
: PTH m
odels
— r
everse
-C
yCle
H
eATing
P
erformAnCe
Heating
Capacity¹
PTH073G
**AXXX
PTH093G
**AXXX
PTH123G
**AXXX
PTH153G
**AXXX
PTH074G
**AXXX
PTH094G
**AXXX
PTH124G
**AXXX
PTH154G
**AXXX
Voltage ¹, ³
230 / 208
230 / 208
230 / 208
230 / 208
265
265
265
265
BTU/h ⁵
6,800 / 6,800
8,300 / 8,100 11,500 / 11,300 13,800 / 13,600
6,800
8,300
11,400
13,700
Amps ¹⁰
3.9
4.2 / 4.2
5.8 / 5.8
7.0 / 7.0
3.1
3.7
5.0
6.1
Watts ¹⁰
585 / 570
715 / 700
1085 /1035
1350 / 1330
570
715
1080
1340
COP ⁵
3.4 / 3.5
3.4 / 3.4
3.1 / 3.2
3.0 / 3.0
3.5
3.4
3.1
3.0
CFM (Dry)
370
360
370
410
370
360
370
410
COP = Coefficiency of Performance; per AHRI Test Procedures, units are rated for capacities and efficiencies.
Notes
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum branch circuit ampacity ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
² Minimum branch circuit ampacity ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
Minimum voltage on 265-volt models is 239 volts; maximum is 292 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must
be cartridge-style time-delay fuses (included and factory-installed on all Amana® brand 265-volt chassis).
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric
heat at approximately 24°F outdoor ambient.
⁶ Specify two-digit heater kW size to complete model number.
⁷ R-410A refrigerant used in all systems.
⁸ All units meet or exceed ASHRAE 90.1 standards.
⁹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹⁰ Refer to electric heat performance data for total MCA and recommended overcurrent protection.
⁷ R-410A refrigerant used in all systems.
⁸ All units meet or exceed ASHRAE 90.1 standards.
⁹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹⁰ Refer to electric heat performance data for total MCA and recommended overcurrent protection.
Amps and Watts notation refers to compressor only.