Amana AMV6502RE 业主指南

■  

For all cord connected appliances:
The microwave oven must be grounded. In the event of 
an electrical short circuit, grounding reduces the risk of 
electric shock by providing an escape wire for the electric 
current. The microwave oven is equipped with a cord 
having a grounding wire with a grounding plug. The plug 
must be plugged into an outlet that is properly installed 
and grounded.

WARNING: 

Improper use of the grounding plug can 

result in a risk of electric shock. Consult a qualified 
electrician or serviceman if the grounding instructions are 
not completely understood, or if doubt exists as to whether 
the microwave oven is properly grounded. 
Do not use an extension cord. If the power supply cord is 
too short, have a qualified electrician or serviceman install 
an outlet near the microwave oven.

Observe all governing codes and ordinances.

■

  A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply 

with a fuse or circuit breaker.

■ 

A time-delay fuse or time-delay circuit breaker.

■

 A separate circuit serving only this microwave oven.

This device complies with Part 18 of the FCC Rules.

Auto Vent Fan (on some models): To keep the microwave 

oven from overheating, the auto vent fan will automatically turn 

on at high speed if the temperature from the range or cooktop 

below the microwave oven gets too hot. When this occurs, 

the vent fan cannot be turned off. “AUTO FAN ON for heat 

circulation” appears in the display.

Dynamic Fan Sensing (on some models): To keep 

the microwave oven from overheating, the auto vent fan 

will automatically turn on at various speeds, depending 

on the temperature from the range or cooktop below the 

microwave oven. When this occurs, the vent fan cannot 

be turned off. “AUTO FAN Sensor Technology for heat 

circulation” appears in the display. As the temperature cools, 

the fan will automatically decrease its speed, then turn off.

Set the cooktop light to turn on and off at certain times. 

Touch OPTIONS/CLOCK to reach the Light Timer submenu, 

and follow the prompts to set the light on time and light 

off time in hours and minutes, or to cancel Light Timer.
NOTE: Light Timer uses 12-hour clock only.

Reset the filter status after replacing and/or cleaning the filters. 

Touch OPTIONS/CLOCK to reach the Filter Reset submenu, 

and activate reset.

Programming tones and signals. Programming tones 

may be turned off, or all tones (including end-of-function 

signals) may be turned off. Touch OPTIONS/CLOCK to reach 

the Sound submenu, then follow the prompts to turn off or 

on the programming tones or all tones.

The Clock is a 12-hour (12:00-11:59) or 24-hour (0:00-23:59) 

clock. Touch OPTIONS/CLOCK to reach Clock submenu, 

and follow the prompts to set the Clock. Clock format 

(12 hours with AM and PM, 12 hours without AM and PM 

or 24 hours) may also be set in the Clock submenu.

With the microwave oven in standby mode, touch the Timer 

control, enter time, then touch the Timer control or the Start 

control. Cook functions may be entered while the Timer 

is counting down. To cancel timer, touch Timer control while 

the Timer countdown is active in the display.

Activate to avoid unintended start. Touch and hold the Cancel 

control for about 3 seconds until 2 tones sound and padlock 

icon appears in the display. Repeat to unlock control.

Ten options/settings may be adjusted: 1-Clock & Energy Save; 

2-Scrolling Speed; 3-Sound; 4-Language; 5-Auto Vent Fan; 

6-Filter Reset; 7-Fan Timer; 8-Light Timer; 9-Demo Mode; 

10-Factory Reset.

Various speeds, ranging from High to Low, and Off. Comes 

on automatically as cooling fan during any cook function.

Vent Timer: Set vent fan to run for exactly 30 minutes, 

or to run for only 30 minutes more (off after 30 minutes). 

The vent fan may be turned off at any time using the Vent 

Fan control. Touch OPTIONS/CLOCK to reach the Fan Timer 

submenu, and select the setting.