Moen YG5412ORB 产品数据表
YG5412CH
– 12” Grab Bar
Chrome Finish
YG5412BN
– 12” Grab Bar
Brushed Nickel Finish
YG5412ORB
– 12” Grab Bar
Oil Rubbed Bronze
YG5418CH
– 18” Grab Bar
Chrome Finish
YG5418BN
– 18” Grab Bar
Brushed Nickel Finish
YG5418ORB
– 18” Grab Bar
Oil Rubbed Bronze Finish
YG5424CH
– 24” Grab Bar
Chrome Finish
YG5424BN
– 24” Grab Bar
Brushed Nickel Finish
YG5424ORB
– 24” Grab Bar
Oil Rubbed Bronze
YG5430CH
– 30” Grab Bar
Chrome Finish
YG5430BN
– 30” Grab Bar
Brushed Nickel Finish
YG5436CH
– 36” Grab Bar
Chrome Finish
YG5436BN
– 36” Grab Bar
Brushed Nickel Finish
YG5442CH
– 42” Grab Bar
Chrome Finish
YG5442BN
– 42” Grab Bar
Brushed Nickel Finish
2 5 3 0 0 A L MO E N D R I V E
N O R TH O L MS TE D , O H 4 4 0 7 0
C O R P O R A TE H E A D Q U A R TE R S : ( 8 0 0 ) 3 2 1 - 8 8 0 9
F A X: ( 8 0 0 ) 8 4 8 - 6 6 3 6
I N TE R N A TI O N A L : ( 4 4 0 ) 9 6 2 - 2 0 0 0
F A X: ( 4 4 0 ) 9 6 2 - 2 7 2 6
C U S TO ME R S E R V I C E ( U S A ) : 8 0 0 - 8 8 2 - 0 1 1 6
F A X: ( 8 8 8 ) 3 7 9 - 2 7 2 0
W W W . MO E N . C O M
Copyright Creative Specialties International
Literature # BA1125
Grab Bar posts and bars are
stainless steel.
stainless steel.
Cleaning Instructions:
1.
Please note that screws MUST be mounted into a wood stud for secure installation.
2.
Slide the end cov er away from the hub end to expose the SecureMount™ mounting flange.
3.
Locate the studs behind the wall by using a stud sensor or other stud locating method. Studs
are usually 16 in. apart; locate the center of each stud.
are usually 16 in. apart; locate the center of each stud.
4.
Place the grab bar on the wall where desired so that the SecureMount™ mounting flange is
positioned ov er a wood stud. Use a level to verify desired placement.
positioned ov er a wood stud. Use a level to verify desired placement.
Decide whether y ou would like to position your grab bar horizontally, vertically or at an angle,
remembering that BOTH ends of the grab bar MUST be positioned over a wood stud.
Note: Diagonal/angled installation is possible only with grab bars 24 in. or longer.
5.
remembering that BOTH ends of the grab bar MUST be positioned over a wood stud.
Note: Diagonal/angled installation is possible only with grab bars 24 in. or longer.
5.
With a pencil, mark three of the mounting locations on each other the two grab bar flanges.
Two marks to be made above the grab bar in the area indicated in the illustration, the third
mark to be made below the grab bar in the area indicated in the illustration.
Two marks to be made above the grab bar in the area indicated in the illustration, the third
mark to be made below the grab bar in the area indicated in the illustration.
To ensure proper installation, the SecureMount™ flange must have screws in each other the
positions indicated in the illustration.
6.
positions indicated in the illustration.
6.
Remov e the grab bar from the wall and drill 1/8 in. diameter pilot holes at the marked screw
locations.
locations.
If desired, apply silicone caulk to the back of the decorative cover to guard against
water penetration.
7.
To mount the grab bar, reposition
one end of the grab bar SecureMount™ mounting flange
ov er the marked holes. NOTE: THE MOUNTING FLANGE WILL ROTATE. ROTATE THE
FLANGE SO THAT IT IS FLUSH AGAINST THE WALL AND THEN PROCEED WITH THE
NEXT STEP.
FLANGE SO THAT IT IS FLUSH AGAINST THE WALL AND THEN PROCEED WITH THE
NEXT STEP.
8.
Using the screwdriver, screw the wood screws into the SecureMount™ mounting flange at one
end of the grab bar. Then screw the wood screws into the mounting flange at the other end of
the grab bar.
end of the grab bar. Then screw the wood screws into the mounting flange at the other end of
the grab bar.
9.
Tighten the screws until secure
10.
Slide the end cov er over the SecureMount™ mounting flange, rotating to find the correct fit
bef ore snapping into place.
bef ore snapping into place.
Stock Number:______________________Tank Lever
By Creative Specialties
By Creative Specialties
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
Grab Bar
YG5400
Kingsley
®
Technical Specification
To preserve the fine finish of this product, clean only with a soft
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
Compliance:
CSI grab bars meet or exceed the applicable
requirements of the follow ing standards:
ANSI A117.1
ASTM F446
CSA B45
CSA B651
Loaded Tested to w ithstand 500 lbs w hen
securely installed pe
requirements of the follow ing standards:
ANSI A117.1
ASTM F446
CSA B45
CSA B651
Loaded Tested to w ithstand 500 lbs w hen
securely installed pe
r instructions. 12” long
grab bars are intended for vertical installation
only.
only.