Dacor RNRP36GSLPH 安装指导

Installation Instructions

Verifying Proper Operation

Before operating the range, read the accompanying use and 

care manual completely. It contains Important safety, service and 

warranty information.
1.  Before beginning the test procedure, ensure that all cooktop 

control valves are in the 

OFF position, and all burner rings, 

burner caps, and grates are properly positioned on the 

cooktop frame. 

2.  Turn on the gas supply at the shut-off valve.
3.  Connect the power cord to the electrical outlet. When the 

range is first connected, the oven indicator light flashes on 

and off for about 10 seconds while the range’s circuitry starts 

up. Wait for the light to stop flashing before going to step 4.

4.  Test one of the burners by pushing the knob in and turning 

it counterclockwise to the 

HIGH position. It may take up to 

four seconds for ignition to occur, at which time the ignitor will 

stop sparking. If ignition does not occur within four seconds, 

turn off the knob, wait for at least five minutes to allow any 

gas to dissipate, then repeat the ignition test. After ignition, 

rotate the control knob counterclockwise from 

HIGH to LOW 

to adjust the flame height progressively. When the range is 

installed properly, the flame will 

be steady and quiet. It will also 

have a sharp, blue inner cone that 

will vary in length proportional to 

the burner size. Dacor’s Smart 

Flame™ feature reduces the flame 

under the grate fingers to increase 

grate life. If the range is equipped 

for use with LP gas, the ends of 

the flame may be yellow at the 

tips, which is normal.

5.  Turn the control knob to the 

OFF position. 

6.  Repeat the ignition test for all remaining burners. 

After testing all the cooktop burners, turn them off.

7.  Open the oven door(s). Test the oven light(s) by 

turning on the light switch(s) on the control panel.

8.  Turn on the convection fan switch(s). You should hear the 

convection fan, located behind the screen at the back of the 

oven, come on.

9.  With the oven door open, turn the oven control knob to the 

400 degree position. Both the knob itself and the oven ON 

indicator light next to the knob should illuminate. Within 60 

seconds you should hear the bake burner ignite below the 

oven floor. It should begin to give off heat.

10.  Turn the oven control knob to the BROIL position. The bake 

burner should turn off. Both the oven control knob and the 

oven ON indicator light should be illuminated.

11.  Within 60 seconds the IR burner on the ceiling of the oven 

should ignite and begin to give off heat.

12.  Turn the oven knob to the “OFF” position. On model 

RNRP48G, test both ovens.

If the range does not operate properly, follow these 

troubleshooting steps:
1.  Verify that power and gas are supplied to the range.
2.  Check the electrical connections and gas supply to ensure 

that the installation has been completed correctly.

3.  Repeat the burner ignition test and/or oven test.
4.  If the appliance still does not work, contact Dacor Distinctive 

Service at (800) 793-0093 ex. 2822. Do not attempt to repair 

the appliance yourself. Have the model and serial numbers 

available when you call. See inside cover for location.

Dacor is not responsible for the cost of correcting problems 

caused by a faulty installation.

Removing the Range for Service

1.  Turn the gas supply valve to the off position.
2.  Disconnect the power cord from the electrical outlet.
3.  Pull the range out from the wall

Reinstalling the Range After 

Service

1.  Push the range into operating position, making sure the anti-

tip bracket is engaged (see page 10).

2.  Connect the power cord to the electrical outlet.
3.  Turn the gas supply valve to the on position.

Installation Checklist

• 

To ensure a safe and proper installation, the following 

checklist should be completed by the installer to ensure 

that no part of the installation has been overlooked.

• 

Proper installation is the responsibility of the homeowner. 

The importance of proper installation of your Dacor range 

cannot be overemphasized.

 

□

Has the plastic coating been peeled off the outside of the 

range? Have all packaging materials been removed from 

inside the oven?

 

□

Are all leveling legs extended down to make contact with the 

floor? Is the unit level? See page 10.

 

□

Is the range secured in place with the provided anti-tip 

bracket and foot according to these instructions? See pages 

6 and 10.

 

□

Has the gas supply inlet pressure been measured to ensure 

that it does not exceed the maximums stated in these 

instructions. See page 3.

 

□

Is the range connected to the gas supply according to these 

instructions and in accordance with all applicable codes? Did 

the installer check the gas supply for leaks?

 

□

Is the oven door properly installed according to these 

instructions? See page 10.

 

□

Have the burner knobs been installed in the proper locations? 

See page 11.

 

□

Are the burners assembled and grates properly installed 

according to these instructions? See page 12.

 

□

Has proper operation been verified? Has the warranty 

been activated on-line or the warranty card been filled out 

completely and mailed?