Frigidaire FGMC3065PB 图
Electronic Oven Control (EOC) Fault Code Descriptions
Code
Condition / Cause
Suggested Corrective Action
F10
Control has sensed a potential runaway oven condition,
control may have shorted relay, and/or RTD sensor probe
may have gone bad.
control may have shorted relay, and/or RTD sensor probe
may have gone bad.
Check RTD sensor probe and replace, if necessary. If oven is overheating, disconnect
power. If oven continues to overheat when power is reapplied, replace the Electronic
Oven Control (EOC).
power. If oven continues to overheat when power is reapplied, replace the Electronic
Oven Control (EOC).
F11
Shorted Key: A key has been detected as pressed (for a
long period). Will be considered a shorted key alarm and
will terminate all oven activity.
long period). Will be considered a shorted key alarm and
will terminate all oven activity.
1. Press
STOP key.
2.
If the problem persists, replace the EOC.
F13
Control’s internal checksum may be corrupted.
•
Press CLEAR key. - Disconnect power, wait 10 seconds, and reapply power. If fault
returns upon power-up, replace EOC.
returns upon power-up, replace EOC.
F14
Misconnected fl at cables. No communication between oven
and controls.
and controls.
1.
Disconnect power. Verify the fl at cable connection between the touch panel or
membrane and the EOC on P12 and P13.
membrane and the EOC on P12 and P13.
2.
If the problem persist, replace the EOC.
F30
or
F31
Open RTD sensor probe/ wiring problem. Note: EOC may
initially display an “F10,” thinking a runaway condition
exists.
Shorted RTD sensor probe /wiring problem.
initially display an “F10,” thinking a runaway condition
exists.
Shorted RTD sensor probe /wiring problem.
1.
Check wiring in probe circuit for possible open or short condition.
2.
Check RTD resistance at room temperature (compare to probe resistance chart). If
resistance does not match the chart, replace the RTD sensor probe.
resistance does not match the chart, replace the RTD sensor probe.
3.
Let the oven cool down and restart the function.
4.
If the problem persists, replace the EOC.
F90
to
F94
Door motor mechanism failure.
1.
Turn off power for 10 seconds, then turn on power. Test the door latch again (try to
start a Clean cycle).
start a Clean cycle).
2.
If it fails, check wiring of Lock Motor, Lock Switch and Door Switch circuits.
3.
Unplug the lock motor from the board and apply power (L1) directly to the Lock
Motor. If the motor does not rotate, replace Lock Motor Assembly.
Motor. If the motor does not rotate, replace Lock Motor Assembly.
4.
Check Lock Switch for proper operation (do the contacts open and close, check
with ohmmeter). The Lock Motor may be powered as in above step to open and
close Lock Switch. If the Lock Switch is defective, replace Motor Lock Assembly.
with ohmmeter). The Lock Motor may be powered as in above step to open and
close Lock Switch. If the Lock Switch is defective, replace Motor Lock Assembly.
5.
If all above steps fail to correct situation, replace the EOC.
Note: Generally speaking, F1X implies a control failure, F3X an oven probe problem, and F9x a latch motor problem.
NOTICE: This service data sheet is intended for use by persons having
electrical and mechanical training and a level of knowledge of these subjects
generally considered acceptable in the appliance repair trade. The manufac-
turer cannot be responsible, nor assume any liability, for injury or damage of
any kind arising from the use of this data sheet.
electrical and mechanical training and a level of knowledge of these subjects
generally considered acceptable in the appliance repair trade. The manufac-
turer cannot be responsible, nor assume any liability, for injury or damage of
any kind arising from the use of this data sheet.
IMPORTANT NOTE: This unit includes an EOC (electronic oven control). This
board is not fi eld-repairable.
board is not fi eld-repairable.
Safe Servicing Practices
To avoid the possibility of personal injury and/or property damage, it is import-
ant that safe servicing practices be observed. The following are some, but not
all, examples of safe practices.
1.
To avoid the possibility of personal injury and/or property damage, it is import-
ant that safe servicing practices be observed. The following are some, but not
all, examples of safe practices.
1.
Do not attempt a product repair if you have any doubts as to your ability
to complete it in a safe and satisfactory manner.
to complete it in a safe and satisfactory manner.
2.
Before servicing or moving an appliance, remove power cord from elec-
tric outlet, trip circuit breaker to Off, or remove fuse.
tric outlet, trip circuit breaker to Off, or remove fuse.
3.
Never interfere with the proper installation of any safety device.
4.
Use only replacement parts specifi ed for this appliance. Substitutions
may not comply with safety standards set for home appliances.
may not comply with safety standards set for home appliances.
5.
Grounding: The standard color coding for safety ground wires is green
or green with yellow stripes. Ground leads are not to be used as current
carrying conductors. It is extremely important that the service technician
reestablish all safety grounds prior to completion of service. Failure to do
so will create a potential hazard.
or green with yellow stripes. Ground leads are not to be used as current
carrying conductors. It is extremely important that the service technician
reestablish all safety grounds prior to completion of service. Failure to do
so will create a potential hazard.
6.
Prior to returning the product to service, ensure that:
•
•
All electric connections are correct and secure.
•
All electrical leads are properly dressed and secured away from
sharp edges, high-temperature components, and moving parts.
sharp edges, high-temperature components, and moving parts.
•
All uninsulated electrical terminals, connectors, heaters, etc. are
adequately spaced away from all metal parts and panels.
adequately spaced away from all metal parts and panels.
•
All safety grounds (both internal and external) are correctly and
securely reassembled.
securely reassembled.
•
All panels are properly and securely reassembled.
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
Resistance (ohms)
1000 ± 4.0
1091 ± 5.3
1453 ± 8.9
1654 ± 10.8
1852 ± 13.5
2047 ± 15.8
2237 ± 18.5
2697 ± 24.4
Open circuit/infinite resistance
RTD SCALE
Temperature °F (°C)
32 ± 1.9 (0 ± 1.0)
75 ± 2.5 (24 ± 1.3)
250 ± 4.4 (121 ± 2.4)
350 ± 5.4 (177 ± 3.0)
450 ± 6.9 (232 ± 3.8)
550 ± 8.2 (288 ± 4.5)
650 ± 9.6 (343 ± 5.3)
900 ± 13.6 (482 ±7.5)
Probe circuit to case ground
807574801 EN Rev A (13/05)
SERVICE DATA SHEET - Microwave Combination Unit with ES525/530 Electronic Oven Control
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged
into the wall oven receptacle that is properly installed and grounded in
accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
This oven is equipped with a three prong grounding plug. It must be plugged
into the wall oven receptacle that is properly installed and grounded in
accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
WARNING: Improper use of the
grounding plug can result in a risk
of electric shock.
grounding plug can result in a risk
of electric shock.
Electrical Requirements
The electrical requirements are a
120 volt 60 Hz, AC only, a branch
circuit protection fuse, 20 amp is
provided in series with the ac outlet
on top of the wall oven support.
The electrical requirements are a
120 volt 60 Hz, AC only, a branch
circuit protection fuse, 20 amp is
provided in series with the ac outlet
on top of the wall oven support.
*Note: Branch circuit fuse 20 amp
shall be replaced with class cc type.
shall be replaced with class cc type.
OVEN CIRCUIT
ANALYSIS
MATRIX
On Relay Board
On Display
Board
ELEMENTS
Oven Light
J3-3
Conv. Fan
J3-5
Door Motor
J3-4
Cooling Fan Low
Speed J3-2
Cooling Fan High
Speed J3-1
DLB L2
Out P1
Bake P9 Broil P7 Conv. P11
Door Switch
P11-4 / P11-3
Preheat
X
X
X
X
X
X
X
Bake
X
X
X*
X*
X
X
X
Broil
X
X
X
X
Convection Bake
X
X
X
X
X
X
X
Convection Roast
X
X
X
X
X
X
X
Convection Broil
X
X
X
X
X
Clean
X
X
X
X
X
Locking / Unlocking
X
Light
X
Door Open
X
Door Closed
X
* Convection element and fan are used for the fi rst rise of temperature.
Relay will operate in this condition only
J4
P11
P9
P7
J3
K11 K14 K16 K18
K7
K5
K3
P5
P6
P11
P15
K9
J3
P2
K1
P3
P17
P1
DOOR SENSING AND PRIMARY INTERLOCK SWITCHES
The primary interlock switch is mounted in the lower position of the latch hook and the
door sensing switch in the secondary interlock system is mounted in the upper position
of the latch hook. They are activated by the latch heads on the door. When the door is
opened, the switches interrupt the power to all high voltage components. A cook cycle
cannot take place until the door is fi rmly closed thereby activating both interlock switches.
The secondary interlock system consists of the door sensing switch and secondary
interlock relay located on the control circuit board.
The primary interlock switch is mounted in the lower position of the latch hook and the
door sensing switch in the secondary interlock system is mounted in the upper position
of the latch hook. They are activated by the latch heads on the door. When the door is
opened, the switches interrupt the power to all high voltage components. A cook cycle
cannot take place until the door is fi rmly closed thereby activating both interlock switches.
The secondary interlock system consists of the door sensing switch and secondary
interlock relay located on the control circuit board.
MONITOR SWITCH
The monitor switch is activated (the contacts opened) by the latch head on the door while
the door is closed. The switch is intended to render the oven inoperative, by means of
blowing the monitor fuse, when the contacts of the secondary interlock relay (RY2) and
primary interlock switch fail to open when the door is opened.
The monitor switch is activated (the contacts opened) by the latch head on the door while
the door is closed. The switch is intended to render the oven inoperative, by means of
blowing the monitor fuse, when the contacts of the secondary interlock relay (RY2) and
primary interlock switch fail to open when the door is opened.
Functions:
1. When the door is opened, the monitor switch contact close (to the ON condition)
1. When the door is opened, the monitor switch contact close (to the ON condition)
due to their being normally closed. At this time the secondary interlock relay (RY2)
and primary interlock switch are in the OFF condition (contacts open) due to their
being normally open contact switches.
and primary interlock switch are in the OFF condition (contacts open) due to their
being normally open contact switches.
2. As the door goes to a closed position, the monitor switch contacts are fi rst opened
and then the door sensing switch and the primary interlock switch contacts close.
(On opening the door, each of these switches operate inversely.)
(On opening the door, each of these switches operate inversely.)
3. If the door is opened, and the secondary interlock relay (RY2) and primary interlock
switch contacts fail to open, the monitor fuse blows simultaneously with closing of
the monitor switch contacts.
the monitor switch contacts.
CAUTION: BEFORE REPLACING A BLOWN MONITOR FUSE TEST THE DOOR
SENSING SWITCH, SECONDARY INTERLOCK RELAY (RY2), RELAY (RY1), PRI-
MARY INTERLOCK SWITCH AND MONITOR SWITCH FOR PROPER OPERATION.
(REFER TO CHAPTER «TEST PROCEDURE»).
SENSING SWITCH, SECONDARY INTERLOCK RELAY (RY2), RELAY (RY1), PRI-
MARY INTERLOCK SWITCH AND MONITOR SWITCH FOR PROPER OPERATION.
(REFER TO CHAPTER «TEST PROCEDURE»).
NOTE:
MONITOR FUSE AND MONITOR SWITCH ARE REPLACED AS AN AS-
SEMBLY.
CAVITY TEMPERATURE FUSE
The cavity temperature fuse located on the top of the oven cavity, is designed to prevent
damage to the oven by fi re. If the food load is overcooked, by either error in cook time
or defect in the control unit, the cavity temperature fuse will open.
The cavity temperature fuse located on the top of the oven cavity, is designed to prevent
damage to the oven by fi re. If the food load is overcooked, by either error in cook time
or defect in the control unit, the cavity temperature fuse will open.
Under normal operation, the cavity temperature fuse remains closed. However, when ab-
normally high temperatures are reached within the oven cavity, the cavity temperature fuse
will open at 302
normally high temperatures are reached within the oven cavity, the cavity temperature fuse
will open at 302
O
F(150
O
C) causing the oven to shut down.
NOTE: This is fuse. It does not reset.
MONITOR FUSE
1. The monitor fuse blows when the contacts (COM-NO) of the primary interlock relay
(RY2) and secondary interlock switch remain closed with the oven door open and
when the monitor switch closes.
when the monitor switch closes.
2. If the wire harness or electrical components are short-circuited, this monitor fuse
blows to prevent an electric shock or fi re hazard.
MAGNETRON TEMPERATURE FUSE
The magnetron temperature fuse located near the magnetron is designed to prevent
damage to the magnetron if an over heated condition develops in the tube due to cooling
fan failure, obstructed air guide, dirty or blocked air intake, etc.
damage to the magnetron if an over heated condition develops in the tube due to cooling
fan failure, obstructed air guide, dirty or blocked air intake, etc.
Under normal operation, the magnetron temperature fuse remains closed. However,
when abnormally high temperatures are reached within the magnetron, the magnetron
temperature fuse will open at 302°F(150°C) causing the oven to shut down.
when abnormally high temperatures are reached within the magnetron, the magnetron
temperature fuse will open at 302°F(150°C) causing the oven to shut down.
NOTE: This is a fuse. It does not reset.
Data Sheet Abbreviations and Terminology
DLB - Double Line Break
EOC - Electronic Oven Control
LED - Light-Emitting Diode
MDL - Motor Door Latch
PS - Power supply board (PS1, PS2,
etc)
etc)
RTD - Resistance Temperature
Detector/Oven Probe
Detector/Oven Probe
TCO - Thermal cut out, also “thermo
disc” or “thermal limiter”
disc” or “thermal limiter”
VSC - Variable Speed Control
J3. Relay Outputs : Convection Fan, Motor Door
Latch, Oven Light, Cooling Fan. Power Input (L1
and Neutral).
Latch, Oven Light, Cooling Fan. Power Input (L1
and Neutral).
P11. Door switch, Motor Door Latch Switch and
Oven Probe Inputs.
Oven Probe Inputs.
P1. L2
Out
P3. L2
In
P5. L1 Input
P7. Broil Connector
P9. Bake Connector
P11. Convection Element Connector
P15. L1 Input
P7. Broil Connector
P9. Bake Connector
P11. Convection Element Connector
P15. L1 Input