Viking RVCH330X 快速参考卡片
Settings and Functions
ALWAYS turn on your hood before you
begin cooking to establish airflow in the
kitchen. Also let the blower run for a few
minutes to clear the air after you turn off
your cooking appliance. This will help
keep the kitchen air cleaner.
begin cooking to establish airflow in the
kitchen. Also let the blower run for a few
minutes to clear the air after you turn off
your cooking appliance. This will help
keep the kitchen air cleaner.
ON/OFF switch—Starts and stops the
blower. When turned on, the blower will
operate at the previous setting of the
speed control.
blower. When turned on, the blower will
operate at the previous setting of the
speed control.
Blower speed knob—Turn
counterclockwise to decrease the blower
speed and clockwise to increase the
speed. The type of cooking you are
doing will dictate the speed of the
blower you use.
counterclockwise to decrease the blower
speed and clockwise to increase the
speed. The type of cooking you are
doing will dictate the speed of the
blower you use.
Light switch—Controls the 50-watt
halogen lights located in the front of
the hood.
halogen lights located in the front of
the hood.
Dimmer knob—Turn the knob
clockwise to brighten the lights and
counterclockwise to dim.
clockwise to brighten the lights and
counterclockwise to dim.
Cleaning and Maintenance
Cleaning Mesh Filters
As air passes through the filter, grease
particles collect on the stainless steel
screen inside the filter. The filters should
be examined periodically to assure that
all surfaces and parts are clean. This unit
is equipped with an alarm. Once the unit
has been in operation for 48 hours, the
letters “FILT” will appear on the display.
The filters can then be washed in a
dishwasher or in a sink with hot, soapy
water. Simple periodic cleaning will
ensure maximum effectiveness. DO NOT
use caustic detergent to clean the filters.
An abrasive or corrosive cleaner may
damage the finish. DO NOT take the
filters apart to clean them. It is not
necessary and will void the filter warranty.
Once the filters have been cleaned and
placed back in the hood, the display is
canceled by holding the scroll up (+) and
the scroll down (-) buttons for 5 seconds.
particles collect on the stainless steel
screen inside the filter. The filters should
be examined periodically to assure that
all surfaces and parts are clean. This unit
is equipped with an alarm. Once the unit
has been in operation for 48 hours, the
letters “FILT” will appear on the display.
The filters can then be washed in a
dishwasher or in a sink with hot, soapy
water. Simple periodic cleaning will
ensure maximum effectiveness. DO NOT
use caustic detergent to clean the filters.
An abrasive or corrosive cleaner may
damage the finish. DO NOT take the
filters apart to clean them. It is not
necessary and will void the filter warranty.
Once the filters have been cleaned and
placed back in the hood, the display is
canceled by holding the scroll up (+) and
the scroll down (-) buttons for 5 seconds.
Maintaining Charcoal Filter
(Recirculating Hoods Only)
Replace the charcoal filters every 6 months
to 1 year depending on the amount and
type of cooking you do.
to 1 year depending on the amount and
type of cooking you do.
To replace, remove the mesh/charcoal filter
assembly and slide the charcoal filter out of
the channel and replace with a new one.
DO NOT put the charcoal filters in the
dishwasher.
assembly and slide the charcoal filter out of
the channel and replace with a new one.
DO NOT put the charcoal filters in the
dishwasher.
Replacement filters are available through
your local Viking Range dealer, or you can
call the Viking Online Store at
1-877-834-8222 or visit vikingrange.com
your local Viking Range dealer, or you can
call the Viking Online Store at
1-877-834-8222 or visit vikingrange.com
C A U T I O N
For general ventilating use only. DO NOT
use to exhaust hazardous or explosive
materials and vapors.
use to exhaust hazardous or explosive
materials and vapors.
3
2
1
1
3
2
1
2
Slide filter front over front lip. Push filter
rear up, then slide back over rear lip.
Slide filter front over front lip. Push filter
rear up, then slide back over rear lip.
Replacing the Light Bulbs
When removing bulbs, use an oven mitt
to protect your hand in case the bulb
breaks.
to protect your hand in case the bulb
breaks.
Cleaning Hood Canopy
Finishes in enamel or stainless steel are
highly resistant to damage or discoloration
due to grease, steam, and heat—provided
that reasonable care is given to the
equipment. The following suggestions will
help keep your hood looking new.
highly resistant to damage or discoloration
due to grease, steam, and heat—provided
that reasonable care is given to the
equipment. The following suggestions will
help keep your hood looking new.
1. DO NOT allow an excessive
accumulation of grease. For best results,
you should wipe your hood clean with a
cloth dipped in warm, soapy water.
DO NOT USE ABRASIVE CLEANSERS,
you should wipe your hood clean with a
cloth dipped in warm, soapy water.
DO NOT USE ABRASIVE CLEANSERS,
STEEL WOOL PADS, OR ABRASIVE
CLOTHS. DO NOT use cleansers that
contain chlorides; the chlorides in the
cleaner could damage the stainless steel
finish. If you need to scrape stainless
steel to remove encrusted materials, first
soak the area with hot towels to loosen
the material, then use a wooden or
nylon spatula or scraper. DO NOT use a
metal knife, spatula, or any other metal
tool to scrape stainless steel.
CLOTHS. DO NOT use cleansers that
contain chlorides; the chlorides in the
cleaner could damage the stainless steel
finish. If you need to scrape stainless
steel to remove encrusted materials, first
soak the area with hot towels to loosen
the material, then use a wooden or
nylon spatula or scraper. DO NOT use a
metal knife, spatula, or any other metal
tool to scrape stainless steel.
2. Every 3 months give your hood a
thorough cleaning. On painted surfaces,
use a new coat of wax. A good wax
cleaner—available at either a grocery or
hardware store—will do both jobs at
once. On stainless steel surfaces, use a
good stainless steel cleaner and polish.
use a new coat of wax. A good wax
cleaner—available at either a grocery or
hardware store—will do both jobs at
once. On stainless steel surfaces, use a
good stainless steel cleaner and polish.
Renewing Enamel Finish
If discoloration occurs, you should
thoroughly polish the finish on your hood
to renew its gloss and luster and to
remove any grease residue which may
have a yellowing effect. Use any good
enamel polish, refrigerator polish, or
automotive polish.
thoroughly polish the finish on your hood
to renew its gloss and luster and to
remove any grease residue which may
have a yellowing effect. Use any good
enamel polish, refrigerator polish, or
automotive polish.
Renewing Stainless Steel Finish
Regular cleaning is the best way to assure
that your stainless steel finish stays bright
and unscratched. Use lemon oil or stainless
steel polish to coat and protect stainless
steel.
that your stainless steel finish stays bright
and unscratched. Use lemon oil or stainless
steel polish to coat and protect stainless
steel.
1
2
1
1
1
2
2
LIGHTS
FAN
PUSH ON/OFF
PUSH ON/OFF
HIGH
LOW
HIGH
LOW
Light switch
ON/OFF switch
Dimmer knob
Blower speed knob
Unscrew halogen bulb.
Replace the bulb with a 120 volt, 50-watt
halogen bulb.
C A U T I O N
DO NOT use a porcelain cleaner or
rough abrasive cleaner.
rough abrasive cleaner.
C A U T I O N
All brass special ordered parts are
coated with an epoxy coating. DO NOT
use brass cleaners or abrasive
cleansers on the brass option parts.
coated with an epoxy coating. DO NOT
use brass cleaners or abrasive
cleansers on the brass option parts.