Gaggenau VG295214CAX 安装指导
6
Technical Data
Total connected load electric: 25 VA
Nozzle Table Wok Burner
Nozzle Table Large Burner
Nozzle Table Small Burner
Installation Procedure
Prepare Installation Space
Create the cut-out in the countertop for one or several
Vario appliances according to the installation diagram.
The angle of of the cut surface to the countertop must
be 90°.
Vario appliances according to the installation diagram.
The angle of of the cut surface to the countertop must
be 90°.
After creating cut-out, remove shavings. Seal cut
surfaces in a heat-resistant manner.
surfaces in a heat-resistant manner.
Some solid surface countertops require special
installations. For example, heat reflective tape and
rounded corners may be necessary. Contact the
countertop manufacturer for instructions specific to
your countertop.
installations. For example, heat reflective tape and
rounded corners may be necessary. Contact the
countertop manufacturer for instructions specific to
your countertop.
Observe minimum distance between appliance
underside and furniture parts of
underside and furniture parts of
3
/
8
" (10 mm).
When installing multiple Vario appliances:
Take into
account space requirement for VV 200 connection
strip between the appliances. Appliances can also be
installed in individual cut-outs, bearing in mind a
minimum distance between the appliances of 1
strip between the appliances. Appliances can also be
installed in individual cut-outs, bearing in mind a
minimum distance between the appliances of 1
9
/
16
"
(40 mm).
Install Appliance
,
WARNING:
Before you plug in an electrical cord
or turn on power supply, make sure all controls
are in the OFF position.
are in the OFF position.
Air intake from above. No intermediate shelf required.
Stovetop clamping range: 30 - 50 mm.
1
Cut out an opening in the countertop according
to the installation drawing. Check the minimum
clearance from the rear wall and the sides of
kitchen units. Seal the edges of the cut-out.
to the installation drawing. Check the minimum
clearance from the rear wall and the sides of
kitchen units. Seal the edges of the cut-out.
2
Turn the clamp fasteners to the side. Place the
gas hotplate into the cut-out and align it evenly.
gas hotplate into the cut-out and align it evenly.
3
Tighten all clamp fasteners evenly. Check that the
whole frame lies evenly flat on the countertop.
whole frame lies evenly flat on the countertop.
4
Fit the burner rings, burner lids and pan supports.
5
Connect the appliance to the gas and electricity
supply. The appliance is not operable without
power supply.
supply. The appliance is not operable without
power supply.
6
Test the appliance for correct functioning. There
might be an air pocket in the gas supply line if the
appliance turns off and the indicator lights flash.
Turn all control knobs to 0 and ignite the burner
again.
might be an air pocket in the gas supply line if the
appliance turns off and the indicator lights flash.
Turn all control knobs to 0 and ignite the burner
again.
Gas
Natural Gas
Type N
Type N
LPG (Propane)
Type X
Type X
Pressure
6" water col-
umn (1.5 kPa)
umn (1.5 kPa)
10" water col-
umn (2.5 kPa)
umn (2.5 kPa)
Nozzle, full burn, outer
173
110 A
Nozzle, low burn, outer
75
56
Nozzle, full burn, inner
60
42
Nozzle, low burn, inner
48
34
Air gap adjustment, outer 0 mm
2 mm
Total connected load
59 700 BTU
(17.5 kW)
(17.5 kW)
58 000 BTU
(17 kW)
(17 kW)
Total consumption
1.67 m³/h
1160 g/h
Gas
Natural Gas
Type N
Type N
LPG (Propane)
Type X
Type X
Pressure
6" water col-
umn (1.5 kPa)
umn (1.5 kPa)
10" water col-
umn (2.5 kPa)
umn (2.5 kPa)
Nozzle, full burn, outer
150
105
Nozzle, low burn, outer
65
45
Nozzle, full burn, inner
40
29
Nozzle, low burn, inner
42
28
Air gap adjustment, outer 0 mm
2 mm
Total connected load
59 700 BTU
(17.5 kW)
(17.5 kW)
58 000 BTU
(17 kW)
(17 kW)
Total consumption
1.67 m³/h
1160 g/h
Gas
Natural Gas
Type N
Type N
LPG (Propane)
Type X
Type X
Pressure
6" water col-
umn (1.5 kPa)
umn (1.5 kPa)
10" water col-
umn (2.5 kPa)
umn (2.5 kPa)
Nozzle, full burn, outer
97
68
Nozzle, low burn, outer
48
34
Nozzle, full burn, inner
40
29
Nozzle, low burn, inner
42
28
Air gap adjustment, outer 0 mm
open at MAX
Total connected load
59 7000 BTU
(17.5 kW)
(17.5 kW)
58 000 BTU
(17 kW)
(17 kW)
Total consumption
1.67 m³/h
1160 g/h