Amana PTH154G35AXXX 规格说明表单
P
roduct
S
PecificationS
8
www.amana-ptac.com
SS-DPTAC
Amana® is a trademark of Maytag Corporation or its related companies and used under license to Goodman Company, L.P. All rights reserved. Our continuing commit-
ment to quality products may mean a change in specifications without notice. © 2014 • Goodman Company, L.P. • Houston, Texas • Printed in the USA.
i
nTAKe
A
ir
f
ilTers
It is extremely important to clean the inlet air filters once a month (or more often if operated in dusty or dirty locations or
conditions) to properly maintain the operational performance of the PTAC unit. The two intake air filters (constructed of
durable polypropylene) can be easily inserted into the cabinet front using the cabinet filter guides. Before cleaning the intake
filters, turn the unit off by setting the mode switch to the OFF position. Filters should be cleaned as required. The following
procedure is used to remove the intake filters:
1. Facing the unit, pull up on the filter handles located at the front top of the unit.
2. Pull each filter upward and remove.
3. Clean filters with vacuum or with running water. Reverse this procedure to reinstall the filters.
conditions) to properly maintain the operational performance of the PTAC unit. The two intake air filters (constructed of
durable polypropylene) can be easily inserted into the cabinet front using the cabinet filter guides. Before cleaning the intake
filters, turn the unit off by setting the mode switch to the OFF position. Filters should be cleaned as required. The following
procedure is used to remove the intake filters:
1. Facing the unit, pull up on the filter handles located at the front top of the unit.
2. Pull each filter upward and remove.
3. Clean filters with vacuum or with running water. Reverse this procedure to reinstall the filters.
Note: Accessory filter kits are available from your sales person. All filters are permanent and cleanable. Consult your
I&O Manual for other monthly cleaning instructions.
s
PAre
f
ilTers
Helps keep dirt and lint out of the air and off the coil,
thus increasing the unit's efficiency. Amana® brand
filters are easy to remove, wash and replace.
thus increasing the unit's efficiency. Amana® brand
filters are easy to remove, wash and replace.
FK10A
10-pack - A Series
FK10B
10-pack - B, C & D Series
FK10E
10-pack - E Series
(requires 2 filters per
change.)
(requires 2 filters per
change.)
r
ePlACemenT
C
HArCoAl
f
ilTer
K
iT
Absorbs airborne odors caused by cigarette, pipe
or cigar smoke and odors caused by mold, mildew,
etc. Filters are made of polyester fibers coated with
activated charcoal and are individually wrapped.
These filters are permanent and can be washed or
cleaned. Call your Amana® brand PTAC sales person
for details. 10 filters per pack.
or cigar smoke and odors caused by mold, mildew,
etc. Filters are made of polyester fibers coated with
activated charcoal and are individually wrapped.
These filters are permanent and can be washed or
cleaned. Call your Amana® brand PTAC sales person
for details. 10 filters per pack.
CFK10A
10-pack - A Series (R-22)
CFK10B
10-pack - B, C & D Series (R-22)
m
onTHly
m
AinTenAnCe
d
uCT
K
iTs
(mdK01e, edK02b, TdK02b, PTdK01e, ddK01e)
Three kits must be supplied to provide ducted, conditioned
air into a second room: a main duct kit, an extension duct kit
and a terminal duct kit.
air into a second room: a main duct kit, an extension duct kit
and a terminal duct kit.
H
ydroniC
H
eAT
K
iT
Is required for heating functions instead of electric resistance
heaters. Unit must retain complete service access with the
kit installed. Proper water or steam valves must be used.
heaters. Unit must retain complete service access with the
kit installed. Proper water or steam valves must be used.
C
ondensATe
r
emovAl
P
umP
(H
eAT
P
umPs
only
)
Must be installed to assist in removing the condensate
developed by the heat pump operation and transfer it to the
indoor coil to dissipate into the room, adding humidity to
the room.
developed by the heat pump operation and transfer it to the
indoor coil to dissipate into the room, adding humidity to
the room.
C
irCuiT
b
reAKer
K
iT
Must be installed in sub-base to provide overcurrent
protection for proper 230/208V amperage. Can also be
used as a physical disconnect where local codes permit for
230/208 voltage.
protection for proper 230/208V amperage. Can also be
used as a physical disconnect where local codes permit for
230/208 voltage.
H
Ard
W
ire
K
iT
Must be used to permanently wire chassis for hard wire
purposes. (For 265V units, Hard Wire Kit may be substituted
with Sub-base Kit.)
purposes. (For 265V units, Hard Wire Kit may be substituted
with Sub-base Kit.)
T
HermosTATs
A manufacturer-approved manual, auto changeover
or programmable traditionally wired thermostat must
be installed to provide full remote operation of the chassis.
A Remote Escutcheon Kit must be used to indicate remote
operation.
or programmable traditionally wired thermostat must
be installed to provide full remote operation of the chassis.
A Remote Escutcheon Kit must be used to indicate remote
operation.
C
onTrACTor
'
s
b
id
s
HeeT
(
ConT
.)