GE PK7000EJES 安装指导

• 

 ,03257$17³ 

Save these instructions 

for local inspector’s use.

• 

 ,03257$17³

 

Observe all governing 

codes and ordinances.

•   Note to Installer – Be sure to leave these 

instructions with Consumer.

•  

Note to Consumer – Keep these instructions 

for future reference.

•  

Skill level – Installation of this appliance 

requires a qualified installer or electrician.

•   Proper installation is the responsibility  

of the installer. 

•   Product failure due to improper installation  

is not covered under Warranty.

•   Product is for indoor use only.

 Before beginning the installation, switch power off at the service panel and 

lock the service disconnecting means to prevent power from being switched on accidentally. When the 

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, 

to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.  

Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, 

stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat  

(up to 200°F [93.3°C]) generated by the oven.

 

Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com 

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

MATERIALS YOU MAY NEED

Junction Box
Wire Nuts
Strain Relief Clamp for 1/2” Conduit

TOOLS YOU MAY NEED

1/8” Drill Bit and Electric or Hand Drill
Phillips Screwdriver
Wire Strippers

  REMOVE PACKAGING MATERIALS

Failure to remove packaging materials could result in damage to the appliance. Remove all packing 

parts from oven, racks and heating elements. Remove protective film and labels on the outer door 

and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping 

screws securing the oven to the base pad. Open oven door and remove literature pack and oven 

racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation 

process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from 

seperate box and set aside (30” Double Wall Ovens Only).

NOTE: If the cabinet does not have a solid bottom, two 

braces or runners must be installed to support the weight 

of the oven. For single ovens, the runners and braces 

must support 200 lbs (91 kg). For double ovens, the 

runners and braces must support 375 lbs. (170 kg).
NOTE: If marks, blemishes or the cutout opening are 

visible above the installed oven, it may be necessary to 

add wood shims under the runners and front trim until 

the marks or opening are covered.
NOTE: If the cabinet does not have a front frame and 

the sides are less than ¾” (1.9 cm) thick, shim both sides 

equally to establish the cutout width.

 

All electric wall ovens must be hard-wired (direct-wired) into an 

approved junction box. A plug and receptacle is NOT permitted on these products.

Suitable 
Bracing 
to Support 

C

L

2" x 4" (5 cm x 10 cm) 

or Equivalent Runners Level 

with Bottom of Cutout

and Flush with Sides of Cutout

SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also 

be installed below a countertop or below specified cooktops. See the label on top of the oven for approved 

models.
DOUBLE OVEN INSTALLATIONS
A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the 

oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for specific 

requirements.