Dacor ER30DSCHNGH 使用和维护

28

Replacing the Light Bulbs

•  To prevent electrical shock and/or personal injury, make 

certain that the oven and light bulb(s) are cool and that 

power to the oven has been turned off at the main power 

supply before replacing the light bulb(s).

•  Always make sure the lens covers are in place when using 

the oven. The lens covers protect the bulbs from breakage.

•  Replacing the lens cover without lining up the cutout with 

the light socket will damage the light fixture.

•  Do not use a screwdriver to remove the lens cover.

Light bulb replacement is considered to be a homeowner 

maintenance operation. If the lights do not work, before 

replacing them, please consult the Problem Solution 

Guide on page 29.
IMPORTANT: Do not touch the replacement halogen light 

bulb with your fingers. Halogen bulbs are sensitive to the 

oils from your hand. The oils from your hand will stick to 

the bulb and may cause it to burn out faster than normal.

1.  Replace the light bulb only with Dacor part number 

100429. See the facing page for ordering information.

2.  Turn off power to the range at the circuit breaker 

panel or fuse box.

3.  Hold your hand under the lens for support and gently 

pry it loose using a spatula or table knife. Pull the lens 

cover straight out.

4.  Grasp the old bulb and pull it straight out of the 

socket.

5.  Using a glove, insert the new bulb into the socket.
6.  As you reinstall the lens cover, line up the cutout on 

the inside rim with the light socket. Gently press it 

into its original position.

7.  Turn the power to the range back on. Reset the clock 

(see page 9).

Care and Cleaning

Light fixture 

in oven wall

Light  

socket

Lens

Lens cutout

Light bulb

Adjusting the Oven Temperature Control

Even though your oven is adjusted at the factory to cook 

at the temperature shown on the display, it may cook 

faster or slower than your old oven.

Do not adjust the probe or self clean offset temperatures. The 

offset for the probe and self clean offsets must remain at 0 for 

proper and/or safe operation.

IMPORTANT: Do not measure the temperature inside the 

oven with a thermometer. Opening the door will cause an 

incorrect reading. Also, the temperature inside the oven 

will vary as the elements cycle on and off.
If you are not satisfied with the results from your oven, 

you can adjust the temperature offset as follows:
1.  With the oven off, press and hold the  

BAKE key for about six seconds.
The current offset temperature will appear 

on the display, for example “0,” if you have not 

adjusted the temperature before.

2.  Enter the new offset temperature.

Within six seconds, enter the amount you 

want to increase or decrease the tem-

perature on the number keypad. To enter 

a minus sign, press the SELF CLEAN key after the 

number(s). A minus sign means that the oven will be 

cooler by the amount shown. When there is no sign 

in front of the number, the oven will be hotter by the 

amount shown. You may enter a number between 

35°F or -35°F (19°C or -19°C). 

3.  Press CANCEL/SECURE to save the 

changes. 
IMPORTANT: If you do not press 

CANCEL/SECURE, your changes will not be saved.

See the chart below for suggestions on the amount you 

need to adjust the oven for the results you want. The 

amount of food browning, moistness and rise time during 

baking will suggest the amount of adjustment you need.

To Cook Food...

Change Temperature By...

A little bit more...

+10°F (+6°C)

Moderately more...

+20°F (+11°C)

A lot more...

+30°F (+17°C)

A little bit less...

-10°F (-6°C)

Moderately less...

-20°F (-11°C)

A lot less...

-30°F (-17°C)